Jump to content
SAU Community

Recommended Posts

Just what speed are you going when trying to shift down to first?

Really you shouldn't even be trying to shift into first if you are still moving

Exactly. First is for leaving the line. You shouldn't be changing into first until you are doing about 5kph.

That's what I do. When traffic is crawling like 5 km/h I change to first and it's hard it move the gearstick in there. I guess I can labour the engine or ride the clutch in second.

Edited by H4x

Even if the synchro on 1st is somehow worn out, a proper heel & toe rev match will allow you to change into 1st at any speed below redline. Of course doing so is only sensible at speeds that are low enough that it won't come on boost in 2nd instantly, but that's another matter.

Learn to drive.

Yeah, you really should stop before trying to put it in first- however if you get into the habit of double clutching you can make it easier on the synchros if you want to put the car in first and you're still moving- pop out the clutch in neutral and rev the engine (ideally to match road speed) before you engage first gear. I am assuming you are attempting to engage first at speeds that are too slow for 2nd gear to be useful.

edit- as above- you beat me to it, darn my slow typing.

Edited by doo doo

I want know what the problem is. Is it a worn synchro or something else? Remember it doesn't crunch while going into first.

Edit:

Also rev matching won't help, double clutching will if its a synchro.

Edited by H4x

mines a little bit sticky even 100% stationary .. usually when this happens i have to put it back in neutral, foot off the clutch, then try again and itll be fine - not really a big issue and doesnt bother me though

Sounds like you have the wrong oil in the box then or rooted oil. Mine is similar to your when its cold but when it warms up its better. My synchro's are a little worn. I would have thought rev matching it would help tho. It helps mine...

Hey, 180ks on the car and I highly doubt it's been changed before (engine oil looked like it had never been changed when I bought the car). I did think about changing the box oil, but there is a oil leak between the block and bellhousing, so I was sort of holding that off until the clutch f**ks out. About the rev matching, how does that help when the clutch is in? Shouldn't you put it in neutral (clutch out) and rev the engine to match your roadspeed then change to first?

Also rev matching won't help, double clutching will if its a synchro.

About the rev matching, how does that help when the clutch is in? Shouldn't you put it in neutral (clutch out) and rev the engine to match your roadspeed then change to first?

I did say heel & toe rev match. That tells you everything about what I meant. Clutch pedal down, move gearstick out of gear, clutch pedal up and roll right foot so ball of foot stays on brake pedal (assuming you're doing it under brakes) and blip throttle with side of foot, clutch back down and move gearstick into 1st, clutch back up with right foot now either firmly pressed on brake (assuming doing it under braking and not wanting to take off just yet) or firmly pressed on accelarator (assuming you've timed your shift correctly and you are now ready to abuse the tyres in 1st).

If you're not doing it whilst braking you can just blip the throttle normally.

Guys need some driving lessons, double-de-clutching is just rev matching.

You don't even need the clutch once your revs are right.

Try an old Mack quad box, only use the clutch for initial take off, then rev match all the rest, no clutch.

Miss a gear and you'll break your wrist.

No synchro on those bad boys.

I didn't say double clutch, because double clutch doesn't actually mean anything (unless you're talking about various modern gearboxes with two clutches). The correct term that you ae thinking of is double de-clutch, but you really only do the classic old style double declutch action in old non-synchro truck gearboxes. When you double de-clutch in a car in a performance context, the action that you use is the heel and toe movement. Nearly everyone that I can think of that knows anything about driving cars knows what heel & toe is. They never say double clutch, but they definitely say heel'n'toe.

^ how do you double clutch?

I have been trying to do this while i drag race ford falcons and holden commodores around the streets like brian did in fast and furious (except he raced american muscle cars!)

i think if i learn to double clutch, i will win, because brian learned to drive and he almost beat vin diesel in the 4th movie with his r34 skyline

i also have a r34 skyline - so if i learn to duble clutch, i think i can beat all muscle cars.

especially since i upgraded my exhorst and put my body kit on.

nyaanyaa.gif

I joke. I was actually gonna write that quote from fast/furious though Allan LOL

yeh mine does the same, hell even when trying to go from 3rd to second it sometimes doesnt want to slot in like it should (similiar to what it does going from 2nd to 1st at lower speeds).. synchros are knackered i believe, changed the oil months ago with no improvement.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
    • Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
×
×
  • Create New...