Jump to content
SAU Community

Recommended Posts

Has anyone fitted 19 x 11 wheels on a R34 GTR?

I've been offered a set as an alternative to 19 x 10 but can't really find much info about wheels that size :)

19 x 11s have an offset of 25 & the 19 x 10s have an offset of 15 - so in theory they should have the exact same stance, so should sit right?

Link to comment
https://www.sau.com.au/forums/topic/378587-11j-wheels/
Share on other sites

You may have to 'adjust the inner plastic guards if the tyre rubs, especially if it's lower than stock.

Also depends on what width tyre you decide to run. 34's are pretty accommodating for bigger, wider wheels.

Mine are 18x10.5 +18 and 275 width is stretched.

Link to comment
https://www.sau.com.au/forums/topic/378587-11j-wheels/#findComment-6038180
Share on other sites

did a quick search and found this if it helps? http://forums.nicocl...34-t288174.html spec sheet is down a little bit

Yeah seen that a few nights ago and got in touch with him :thumbsup:

He said they only had to trim the rear liner a bit to get them to fit comfortably :D

Quite excited now about recieving mine :banana:

Link to comment
https://www.sau.com.au/forums/topic/378587-11j-wheels/#findComment-6043411
Share on other sites

  • 2 weeks later...

I finally got some tyres fitted to these today & I can now confirm that a 295/30/19 on a 19 x 11 ET25 will NOT fit on a R34 GTR :(

They fit perfectly & look amazing - unfortunatley the car is undriveable as on even partial lock the inside of the wheels are knocking against the suspension :(

I'm hoping to get hold of some 5mm spacers & see if it pushes them out far enough to avoid the arms

A couple of pics of them fitted though, stock wheels have been refitted now though while I search for a solution

IMG_0008.jpg

IMG_0009.jpg

IMG_0010.jpg

Ignore the white tyre fitting crap around the wheels, I need to give them a wash :)

Link to comment
https://www.sau.com.au/forums/topic/378587-11j-wheels/#findComment-6063264
Share on other sites

They look massive diameter wise in that picture.

How much do they stick out now with the 10mm?

Drive it over bumpy areas and see if it scrubs on the outside/guard.

19x10.5 +12 and 15mm spacers were scrubbing on the rears. Left a nice thin cut all around my tyres.

Link to comment
https://www.sau.com.au/forums/topic/378587-11j-wheels/#findComment-6066996
Share on other sites

With a 10mm spacer it sits pretty much flush with the arch.

There will be some rubbing, especially once lowered. I think it will be a case of rolling the arches or possibly even Z-tune arches to give a bit more clearance :)

Link to comment
https://www.sau.com.au/forums/topic/378587-11j-wheels/#findComment-6067536
Share on other sites

damn, pity I didn't see this thread earlier, could have warned you off them...

Anyway, for people searching in the future, I'm running 18x11 +18 and they touch the suspension upright before full lock, so not ideal. I'll probably try and get some 5mm spacers to just get them out far enough to clear, but they're pretty much flush with the guards as is.

Does look good though.... :D

Link to comment
https://www.sau.com.au/forums/topic/378587-11j-wheels/#findComment-6072919
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
    • To be fair it's the other way around. 300kw is boring in a modern Golf or BMW. They are so competent / well-engineered / devoid of emotion that you have to go stupid fast to feel anything. Whereas the <300kw RB still makes all the right noises and it feels good to drive. Can pull off at the lights with the turbo whooshing and the blow-off pssshing and feel like the coolest kid on the block. Just don't look to the side where you'll see the bored housewifes in their shitbox Yaris/Corolla/Camry that kept up because you didn't go fast at all
    • 300kW is so boring in a Skyline, you'll get spanked by someone's mum's Golf with Alibaba pipes, and an email tune.
×
×
  • Create New...