Jump to content
SAU Community

Recommended Posts

Hey guys,

so recently my car has started overheating and only had my major service done 6months ago which I put a new water pump in and had the radiator flushed and so on..

Last week got my new clutch put in n since then been over heating :( doubt it would have an input on over heating lol

But thermostat seems to be opening normally but oil temp jumps to about 110 normal driving n my water temp sky rockets almost 140 :( Also noticed on idle oil pressure sits at bout 2kg/cm2 maybe a fraction under thought it sat a little higher on idle?

anyone know what it could possibly be..

Link to comment
https://www.sau.com.au/forums/topic/379440-over-heating-help/
Share on other sites

may be that your radiator is blocked (doing a flush won't help this, would need to be professionally cleaned or a new radiator).

it may also be that while your thermostat is opening at the right temp, it simply isn't opening far enough. i'd start with a new thermostat and then go from there.

Does it overheat on the highway or more around town in traffic ?

A fairly easy way to test your radiator for blockages is to take it out, boil the jug, turn the radiator on its side and fill it up with hot water. Then place your hand all over the fins and feel for any cold spots.

My car was overheating on the highway which meant i had a flow problem which was either water pump or blocked radiator. Turns out my radiator was about 50% blocked.

I tried my best to clean it out and i did get alot of crap out of it but not enough, it was still fairly blocked.

I got myself a second hand factory radiator off a member here for $50,, no blockages,, beautiful.

More start stop driving it happens..have a feeling its the thermostat :s its the only thing that I havent replaced on th car haha but yeah noticed oil temp rises first and when it gets to bout 100 water temp starts rising and I can flick the heater on and water temp drops back to normal but oil temp just gets hotter.. ill take th radiator out today n try that though

yeah flushing a radiator does little to tell you if it's blocked. the build up that blocks it isn't easily shifted. you could liken it to degreasing an engine using just plain water (and not a pressure cleaner). proper radiator flushes don't do much either. using the same analogy, they are like using a weak degreaser. they will take off any light oil, but won't do anything to the baked on grease (now it's starting to sound like a dishwasher detergent ad)

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...