Jump to content
SAU Community

Ecu Reset -- Final Verdict!

Danzil

By Danzil,
in Western Australia

 Share

Recommended Posts

Danzil Enthusiast

Danzil

Posted
Posted

Yeah i know i know...i've searched and i've read all there is to read.

But theres too much of it and theres really no clear winner.

Still don't know wether to do it or not...?? Help

Thus i was wondering who has actually DONE IT....has it made a DIFFERENCE...and more IMPORTANTLY since some might have done it a while back have there been any negative affects you've noticed since doing it.

Ohh and has there been a universal agreement on whats the most efficient way of doing it? WHAT WORKS BEST.

I just got my straight through exhaust and i've heard its wise to do it after each mod...? What u guys think?

Thanks

-Dan

Link to comment
https://www.sau.com.au/forums/topic/37970-ecu-reset-final-verdict/
Share on other sites
rev210 Grand Master

rev210

Posted
Posted

It does take two seconds to do. If your car is not running rough then it won't do anything at all. It does nothing to any of the fuel or ignition maps, possibly helps calibrate closed loop operation but, that doen't affect the power of your car at all.

After evey mod? I didn't bother to do it when I had a gtst. It's not by definition 'wise' becasue it's ignorant of the fact of how the ecu actually does work. Go pick your nose instead, there are more gains to had there for roughly the same time spent.

zanda Grand Master

zanda

Posted
Posted

nice reply rev!

charmer.

the biggest difference it will make is if your car's been pinging.....

the computer will retard to avoid detonation. resetting clears this but if the issue is something more than just a bit of a hot day you will find it pinging and be back to square one in minutes.....

Jay95R33 Grand Master

Jay95R33

Posted
Posted
I have a '95 GTS-t and when I changed from a HKS Pod -> K&N Paneil Filter (in the standard airbox) I had rough idling. This was fixed after resetting my ECU.

Same here, ditched the HKS pod and when to stock airbox = dodgy idle.

ECU reset = nice idle :D

J

rev210 Grand Master

rev210

Posted
Posted

The idle is part of closed loop operation.

As for pinging. If you find your car pinging it will change nothing doing an ecu reset, unless of course the pinging is during very light throttle cruising, because the ecu does not change the ignition map or the fuel map at all. The ecu will still retard the ignition based on the knock sensor feedback exactly the same way regardless.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...