Jump to content
SAU Community

Recommended Posts

Ok, sorry for such a n00b basic question, but I couldnt figure this for the life of me.

Is there a way to identify an RB30 block without actually removing the engine from the car?

Mate just bought an R32 and has suspicions that theres an RB30 block under the 25 head.

Is there a code or something that we can look for?

Ive had a look around and all Ive found is 75T written on the passenger side.

Any help is much appreciated guys :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/379801-rb30-identification/
Share on other sites

Is the car NA? The RB25 head in a 32 with a turbo is a sign of things being a bit "special"! There are lots of clues if you know what to look for, but mad082 is right, look at the engine number, it will start with RB30#####.

on the passenger side of the block right at the bottom where one of the gearbox bolts goes into theres a small machined surface, clean it off and it'll have rb30 stamped on it if is one.

other giveaways would be a gap between the top and bottom timing cover, grinder marks around the bottom of the exhaust manifold near the block and clearance issues.

Ok cheers guys Ill get him to take a look near the gearbox. :cheers:

I did notice a small machined surface close the the gearbox, but it was covered in dirt and crap so thats probably why we didnt notice anything.

It is turbo with greddy intake to solve bonnet clearance which is why we thing the rb30 is in it, and has the heatshield over the exhaust manifold so we cant see anything unless we take it off.

The guy he bought it off had no idea about cars, so was only going off what the previous owner had told him. Apparently there was an rb30 in it, or maybe still is. When he bought it it had a fairly beefy fuel system, custom exhaust and intercooler piping. and thats a bit extreme for a "stock rb25" as the guy thought it was. Seems a bit odd that the previous owner would take the rb30 out, put a 25 in, and fabricate custom piping for it?

Unless he blew it up or something :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...