Jump to content
SAU Community

Recommended Posts

There's nothing to tune on a stock car, is what he's saying.

You can wind in base timing for minimal gains in power, that's it.....

Or tamper with the AFM calibration.....

Edited by blk94r33
Link to comment
https://www.sau.com.au/forums/topic/380002-dyno-tune/#findComment-6059629
Share on other sites

ah yep.

yeah I cant say it would be overly worth it.

Id put that money into some fresh spark plugs, air filter, quality oil (s), clean the afm and a new O2 sensor- and even some new tyres.

you will get way more of a performance enhancement from doing that than a blanket tune on an NA, especially if these aforementioned things havent been done...

Link to comment
https://www.sau.com.au/forums/topic/380002-dyno-tune/#findComment-6059804
Share on other sites

CAS (Ignition Timing) + O2 Sensor Checkup + A'PEXi SAFC NEO.

And some F&F Stickers LOL JK, but srsly just keep it stock and save up for an R32 GT-R or something. The above would probably set you back $400 - $800 but you're not really going to notice any gains + NA Skylines are slow as is... with the above it's still going to be slow, lol.

Link to comment
https://www.sau.com.au/forums/topic/380002-dyno-tune/#findComment-6060149
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...