Jump to content
SAU Community

Recommended Posts

Hi all,

At the moment my car has few mods being as follows:

1. blitz return flow cooler

2. K&N drop in panel filter

3. Excedy HD clutch

4. boosted 1 bar

It also came with an Impul tuned ECU and Nismo VSS muffler.

After searching for what type of exhaust I will need etc, I have decided to change the exhaust system to a 3". However, I want to keep the Nismo muffler, and change the dump/front/cat-back (if that can be done with the VSS).

Does anyone know if the VSS muffler (silent/sports mode) is particularly restrictive? Or whether it would even matter as its at the end of the exhaust?

If people dont know the muffler i'm talking about it can be found here:

http://www.skylinesa..._1#entry5322488

and here:

http://www.skylinesa..._1#entry2851890

Also, once I have changed the exhaust the car will most likely need a tune. Does anyone know if the Impul chip can be tuned? I am pretty sure the car came with both the chip and muffler from factory.

Thanks for your help in advance.

Edited by O_Sotiris

r u after the sotck look or the just the adjustable valve? if u dnt care abt loosin the stock look jsut get a varex cannon with the adjustable valve or if u want the stock look just take it to an exhaust shop and they will make an adapter for the tip..

i personaly rekon it will be a restrictive due to the 2.5" inlet.. u could get a twin varex tip to look similar aswell.. and even rewire it to the vss switch or just use the remote provided.. the varex is exactly the same system as the nismo one.. hope that helps

Cheers

Herb

Better off with a legal exhaust than one that is illegal (valve based) given you are in Vic.

There are a few 3inch items that do pass EPA for when you get pinned.

You will need a prope tune as well. I feel sorry for your car being forced with that boost on a shit stock dia exhaust, can't be good at all.

I actually feel the jap tuned ECU's can be quite good and wouldnt go as far as to say 'need a proper tune'.

The jap ones are normally done around factory based cars with typical mods such as exhaust cooler and boost. But I am a firm believer you should always run them up on the dyno to make sure they are doing what they hope they are.

The variance in fuel between the two countries CAN throw them off completely and leave you detonating the shit out of your motor. No guarantees unless you get it checked!

Hi im currently running the same nismo vss muffler at the end of a 3 inch pipe with the valve removed.

I have a 3071r with AVO rear housing. plus supporting mods and im achiving 274hp at wheels on 9 psi.

Im yet to turn the boost up.

Thanks for the help/opinions guys.

@GTXR34 & R31NISMOID

I like the idea that the car came from factory with the Nismo muffler and the switch in the cabin is a good talking point! Obviously though if it is doing damage i'm not keeping it on. To tell you the truth I never realised it was only a Nismo muffler. I actually thought it was the whole exhaust which is why I haven't upgraded it.

You will need a prope tune as well. I feel sorry for your car being forced with that boost on a shit stock dia exhaust, can't be good at all.

Can the smaller exhaust really be doing doing damage? Will too much backpressure wreck the turbo?

I'm only asking because the car came like that from Japan. Only modifications I have made are the cooler/intake/clutch.

I actually feel the jap tuned ECU's can be quite good and wouldnt go as far as to say 'need a proper tune'.

The car hasn't detonated in the time (almost 2 years) I have had it. It's actually been running a little bit rich, even with the modifications.

Hi im currently running the same nismo vss muffler at the end of a 3 inch pipe with the valve removed.

Do you need some sort of adapter to go from 3" to 2.5" at the muffler?

I made the whole exhaust myself and did a 3 inch to twin 2.25 to use both imput hole in the muffler.

It was a bit of stuffing round but hasnt hurt the power at this low boost i will find out if it does when i get a final tune done.

I think you'll find the impul ecu cannot be tuned but you may be able to replace the chip - ask someone like Toshi - he may be able to do it but you really want it done in your car not by mail.

But if you can stick it on a dyno after you have made the changes - if you're lucky and afrs and timing are acceptable you won't need a retune at this point.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...