Jump to content
SAU Community

Recommended Posts

im going to do new plugs on next service in 500km any suggestions?

im going to get a high flow panel filter and ill clean the afm no problems

but atm probably cant afford a O2 sensor

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

ive never had the light on the dash and have twice had the pin under the empty line

pretty sure that the low fuel light is operated seperately to the dash gauge. as i said earlier, it generally comes on with around 10L left before empty, so if you have never gotten down to a point where it has taken over 55L to fill then you haven't gotten the tank low enough

pretty sure that the low fuel light is operated seperately to the dash gauge. as i said earlier, it generally comes on with around 10L left before empty, so if you have never gotten down to a point where it has taken over 55L to fill then you haven't gotten the tank low enough

correcto mutcho, when you pull the sender unit out you can see a switch thing on the very bottom of sender unit itself but it will only work if the float touches the switch on the unit. So if the sender is giving false readings saying your are empty (fuel gauge can be on 'E') but then the float will not be in contact with the switch on the assembely because you still have more fuel than what its showing on the gauge.

Edited by central coast person

im going to do new plugs on next service in 500km any suggestions?

im going to get a high flow panel filter and ill clean the afm no problems

but atm probably cant afford a O2 sensor

well im not sure what to say but the fact is that its the O2 sensor that causes poor economy, particularly if u are still getting poor economy when driving the car nicely.

They are less than $100 delivered from the business traders on here n u can change it yourself- peice of piss...

do you have an ECU you can tune with?

If not

I dare to to put a tank load of E85 in the car and run on the standard ECU....post video's for lulz

i dare him to put a tank of e85 in and then try to drive out of the driveway of the servo without needing a towtruck, LOL

fixed your post for lulz

=.=

Just an FYI, my search for a glaring face on the internet lead me to imgur.

From there I proceded to redit.

From there, I proceded to very random places.

And hour later, I had forgotten about this post until I was closing my tabs ><

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...