Jump to content
SAU Community

Recommended Posts

1993 R32 GTR

140,000 KMS – Engine rebuilt using standard parts at 96,000 KMS (have receipts)

Engine:

N1 turbos

HKS mushroom pod filters

HKS blow off valves

PWR 42mm full alloy radiator & silicon hoses

Spitfire coilpacks

Reconditioned ignitor (genuine Nissan)

Brand new coil pack loom (genuine Nissan)

Brand new NGK platinum sparkplugs

Walbro intank fuel pump

Kakimoto cat back exhaust 3.75” to 4.5” tip

Apexi PowerFC L-Jetro

GFB manual boost controller (12PSI)

Injectors cleaned and flow tested

Gates timing belt

New standard water pump (genuine Nissan)

Suspension:

Custom ‘Sydney Kid’ Setup

Revalved Bilstein shocks & additional circlip grooves

King springs (low)

ARC front castor arms

Reconditioned rear lower control arms (genuine Nissan)

Rear alloy cradle bushes

New rear inner HICAS rack ends (genuine Nissan)

New dust covers and bump stops

Firm ride and great handling.

Interior:

Recaro racing seats

New gear and handbrake boots

Isotta steering wheel

Ultra Turbo timer

White NIZMO 320km display

Bubble free dashboard

Transmission & Clutch:

Exceedy heavy duty clutch

Unknown short-shifter

Exterior:

Front Bar just resprayed

Great condition bottom lip installed

Additional top grill deflector

ENKEI RP01 (white) some rash on all 4

Federal 235/45/17 all around 90% front, 100% rear

Sound:

Sony Xplode Bluetooth & AUX headunit

Focal components front and back (both have crossovers)

Alpine 4 channel amp

Sound deadening used in doors

If you are looking for a cheap, molested gtr or a high horsepower Sunday prancer this is not the car for you, if you are after a quality, cared for classic then read further. I purchased the car two years ago with the intention of never selling, this which was my justification in purchasing superior parts when cheaper items were available. It has been my reliable daily drive for 2 years however in order to continue my career I have had to go back to University. I have always erred on the side of safety hence the overkill with the radiator, ignition system and only running 12PSI. The car still puts out 220kws at 12 PSI (dyno printout available) and the white on white scheme is subtle but classy. I’m after 20K, the car owes me a lot more but we drive these types of cars for pleasure, not investment. Car is located in Brisbane, will be sold with standard plates and RWC will be supplied.

Michael

0412131599

Mykal_Duhig(at)Yahoo.com.au

post-8342-0-30221400-1319263275_thumb.jpg

post-8342-0-70452800-1319263285_thumb.jpg

post-8342-0-83342000-1319263296_thumb.jpg

post-8342-0-79046500-1319263305_thumb.jpg

post-8342-0-80798200-1319263315_thumb.jpg

post-8342-0-75479200-1319263325_thumb.jpg

post-8342-0-12033900-1319263334_thumb.jpg

post-8342-0-32809300-1319263345_thumb.jpg

post-8342-0-83903600-1319263362_thumb.jpg

post-8342-0-65200900-1319263371_thumb.jpg

post-8342-0-80797300-1319263384_thumb.jpg

Edited by CGB_R32
Link to comment
https://www.sau.com.au/forums/topic/380910-1993-r32-gtr/
Share on other sites

Thanks for the kind words. I should add that the car will come with a brand new (not installed) mongoose M60B alarm (turbo timer and 2 point immobilizer)and has just has its QLD registration extended to April, 2012. Cheers.

Link to comment
https://www.sau.com.au/forums/topic/380910-1993-r32-gtr/#findComment-6077466
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Be patient man. If this was a few months ago, I would have grabbed it. A white 32GTR is PERFECT, the best colour on a 32 IMO - knowing the fact that it had a rebuild not toooooo long ago is an added bonus. Be patient and it'll sell sooner or later, good luck man, she looks great

Link to comment
https://www.sau.com.au/forums/topic/380910-1993-r32-gtr/#findComment-6152318
Share on other sites

still for sale how much without running gear

thanx

I will keep it and live off bread and water before I do something drastic like this.

Or as Sinista said, it's yours for 20K :nyaanyaa:

Link to comment
https://www.sau.com.au/forums/topic/380910-1993-r32-gtr/#findComment-6171545
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...