Jump to content
SAU Community

Recommended Posts

hey guys, have an RB20 tuned on E85 to 250rwkw on 18psi, it's a track car, but it seems to be fouling the plugs every few track days. some come out covered in carbon, some ive pulled out before that almost looked like water corrosion a bit with what looks like rust on the bottom of the thread. they are BCPR6E's gapped down to .7mm

wondering if it's worth changing the heat range for these now i'm running E85, or is the issue possibly in the ignition system which is causing them to not ignite properly, which might be causing the fouling? cold start is irrelevant, as long as she's on song when it's warmed up and ready to go.

i've read a few threads, but the main one on the topic of plugs with e85 turned into a shit fight about e85 itself.

cheers

Link to comment
https://www.sau.com.au/forums/topic/382019-plugs-for-rb20-on-e85/
Share on other sites

it's dry/matte and comes off quite easily, not sure if there's a way burning oil can give that effect, but i just assume carbon. it only really appeared on 2-3 of the plugs, but that itself would explain the slight miss i was getting after a few events.

ignition system from the coilpacks to plug is fresh, running AU coilpacks with leads, probably should have mentioned that haha. coilpacks are brand new, leads are new etc etc. was gonna measure for voltage drop, but haven't had time.

The part number on those plugs, is that BCPR6E or BCPR6ES ? (ie: did you put the apostrophe "s" after for plural or was that part of the part number?)

The reason i ask is that they are different plugs & no "s" is not the right projection for an rb!

as mentioned.. there is vertually zero carbon build up in an e85 fuelled engine. will be clean as a whistle inside. however if its rich and you do a lot of cold starts it will have a lot of condensation/moisture build up leading to the corrosion you see

The part number on those plugs, is that BCPR6E or BCPR6ES ? (ie: did you put the apostrophe "s" after for plural or was that part of the part number?)

The reason i ask is that they are different plugs & no "s" is not the right projection for an rb!

good call mate, they were 6E's, just bought some 6ES's, will probably chuck them in tomorrow, i doubt it'll do much whilst still fresh, but if anything hopefully they don't foul up as quick. how does it affect the RB's? is there all that much difference between the V and the flat faced one?

The part number on those plugs, is that BCPR6E or BCPR6ES ? (ie: did you put the apostrophe "s" after for plural or was that part of the part number?)

The reason i ask is that they are different plugs & no "s" is not the right projection for an rb!

ermmm...any info to back this claim up?

BCPR6ES = Standard electrode

BCPR6E = V-groove electrode. NGK claims Improved ignitability due to sparking at periphery of the electrode.

250kw, I would go 7's. As mentioned on NGK website:

============

Example Take a Holden engine which as standard uses a BPR 5ES spark plug. (The heat range for this spark plug is 5, please refer to our part number identification for further information) If a customer were to install a turbocharger, intercooler and exhaust system to this vehicle, it would be suggested to start with a spark plug with a 7 heat range (BPR 7ES) to be on the safe side. The customer would then need to perform some road testing,

* firstly applying half throttle

* then inspecting the plugs,

* ¾ throttle then again inspecting the plugs

* and eventually full throttle.

At any stage of inspection if the plugs upon removal are very clean and white along the insulator nose this would indicate that the spark plugs are reaching their upper temperature threshold and as such obviously may not withstanding the temperature at full throttle. Fouling a set of spark plugs is very cheap compared to the cost of the engine modifications performed and insignificant compared to the amount of research and design that goes into producing the engine by a vehicle manufacturer.

==========

Nice cut n paste rekin, anyway.... Proof, if you have em on the shelf or next time you are at your local parts store, get them to put all three (E, ES, EY) on the counter and look at them, all the proof you need!!! (& for the hell of it get a BKR plug aswell)

BCPR#E is not the same as a BCPR#EY, yes both are v-groove (E used to be solid), but there is a projection difference (quite significantly shorter in E, ie: will foul quicker in an RB)!

Simply looking at a website or catalogue doesnt make you a professional parts interpreter, a little knowledge can be dangerous!

Why is there a solid 's' and a v-groove 'y', well not really sure why solid hasnt been made redundant yet, as the v-groove is superior & the same price, but many car makers still recommend solids, so eh!

CP vs K

NGK_CPvsK.jpg

The BKR is shorter! Doesn't this mean that the coil pack wont be making as good a connection as the longer CPR? As the BKR plug will be sitting down lower in the valley.

The BKR would be fine with a set of external coil packs with ignition leads. But if your using old coil packs especially with worn out graphite electrodes, there wont be too much of a good connection.

Edited by kitto

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...