Jump to content
SAU Community

Recommended Posts

im currently trying to get my R31/RB25 turbo registered in NSW. took it for an emissions test today and completely failed

using all stock parts for the emissions test bar a 3" exhaust, turbo is at 7 psi.

high flow CAT(i think this may be causing alot of the problem it may be screwed)

any advice on wtf went wrong would be great

here are the test results.

post-88957-0-21318200-1320668750_thumb.jpg

Edited by r31rb25help
Link to comment
https://www.sau.com.au/forums/topic/382353-rb25-failed-nsw-emissions-test/
Share on other sites

Yep.

And why do u need an emmisions test with a standard ecu? Have the rules changed? Try another engineer

apparently i need the test because the engine im using is imported.

im thinking i should just replace the entire exhaust system on it for something with passing this damn test in mind

and i dont know what to to about it dumping about 2x the fuel its allowed to into the exhaust at the moment,

Edited by r31rb25help

dug up my old stock exhaust and put 2 3way CATs on it after some advice from a mechanic, looks like horrid and runs horrid but it will apparently pass.

he also recommended i dont run my intercooler at all just a "straight" pipe.

dug up my old stock exhaust and put 2 3way CATs on it after some advice from a mechanic, looks like horrid and runs horrid but it will apparently pass.

he also recommended i dont run my intercooler at all just a "straight" pipe.

blink.gif

He's trolling for sure. Ask him if he will pay for the new engine after yours goes bang from detonation?

apparently i need the test because the engine im using is imported.

im thinking i should just replace the entire exhaust system on it for something with passing this damn test in mind

and i dont know what to to about it dumping about 2x the fuel its allowed to into the exhaust at the moment,

why is it dumping 2x fuel it should be into the exhaust? if it is overfueling heaps then theres no way it will pass have you got bigger injectors in it or something?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • oh they were with that motor, you need to remove the engine to change the spark plugs (don't have to, but it does make it easier)
    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
×
×
  • Create New...