Jump to content
SAU Community

Ring Gear Stopper

ZED X

By ZED X,
in South Australia

 Share

Recommended Posts

ZED X Rising Star

ZED X

Posted
Posted

hey guys,

Wondering if anyone might have a ring gear stopper for an rb26 I could borrow?

I've tried everything I can think of to crack this crank bolt.. It ain't coming off.

I've tried:

3m breaker bar trans in 4th

wooden block on chasis rail then cranking the starter

breaker bar tensioned then belting it with a 1kg hammer

holding the fly in place using two flat end screwdrivers

couldn't fit a rattle gun without moving the condensor...

I'm finding it difficult to get enough of a sudden jolt onto the crank bolt, hoping if I can hold the in place I might be able to crack it with my breaker bar.

Any help would be greatly appreciated!!

Link to comment
https://www.sau.com.au/forums/topic/382559-ring-gear-stopper/
Share on other sites
Aberax Grand Master

Aberax

Posted
Posted

I found it easy to do it this way.

1. Take out radiator and Clutch fan

2. Put car in 5th, so it is over a 1:1 ratio

3. Put correct size socket with breaker bar onto the bolt

4. Hop in the engine bay and jump up and down on the breaker bar

...worked for me :P

I have heard of people making sure the end of the breaker bar is on the ground and then turning the engine over...but that is a rather bad way of doing it I would say.

ZED X Rising Star

ZED X

Posted
  • Author
Posted

Hey Aberax,

Cheers for the suggestion, however I can't seem to get enough of a sudden shock while using this method. My crank simply turns over, mind you this is with the vehicle on a set of ramps, hand brake up and back wheels chocked. I really need to lock the flywheel then use this method.. ;(

It's on there BLOODY tight... That's for sure.

Race__24 Experienced

Race__24

Posted
Posted (edited)

You need one of those tools that you hit with a hammer. I ended up having to buy one for the same bolt. Cost me over $100 but does it easy. I'll see if i can find a pic.....

One of these. They say they can generate 500nm of torque, I say they aren't using a big enough hammer. You will be able to undo it with the car out of gear so you will avoid putting load through the drive train.

sp70865.jpg

I may lend it out for liquid renumeration

Edited by Race__24
Moodles2 Grand Master

Moodles2

Posted
Posted

When I had my 100,000km service done, we used a breaker bar against the chassis. My battery wasn't enough to do the job, but his big ass BMW battery (I think from a 4WD) loosened it first try

ZED X Rising Star

ZED X

Posted
  • Author
Posted

When I had my 100,000km service done, we used a breaker bar against the chassis. My battery wasn't enough to do the job, but his big ass BMW battery (I think from a 4WD) loosened it first try

Yea Ive got a 550CCA battery if that method was going to work im sure it would have after the first 5 > 10 tries :)

SkyHi_33 Mentor

SkyHi_33

Posted
Posted (edited)

There is a really easy way of doing it,

Socket and breaker bar on crank bolt, place it so the handle of the breaker bar is leaning against the chasis rail/inner well on the undo side or as close to as possible, disconnect your ignition system (unplug coilpack loom), give it a quick short crank with the key, Presto!! Starter motor does all the muscle work for you :)

Edited by SkyHi_33
Simon-S14 Grand Master

Simon-S14

Posted
Posted

You need one of those tools that you hit with a hammer. I ended up having to buy one for the same bolt. Cost me over $100 but does it easy. I'll see if i can find a pic.....

One of these. They say they can generate 500nm of torque, I say they aren't using a big enough hammer. You will be able to undo it with the car out of gear so you will avoid putting load through the drive train.

sp70865.jpg

I may lend it out for liquid renumeration

ive been looking for one of these for a while now.. where did you get yours from?

chef_stagea Grand Master

chef_stagea

Posted
Posted

Y not go the slip knot rig? Easy as pie! And costs f**k all!

Old bike tube cut up, slip knot done to tighten itself as your pulling.

Breaker bar, i cut down a no parking sign out the front of my house for added leverage ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • Duncan
      Who has a Infiniti Q60, Q50 (V37)?

      By Duncan · Posted

      In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      If you are Ecutek tuned then these TCU tunes are anywhere from $550 to $700 usd. If you are not ECUTEK tuned, then it gets costly!    
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
×
×
  • Create New...