Jump to content
SAU Community

Recommended Posts

Hi I’m after some help as my r33 gtst s2 rb25det needs arebuild.

I’m after advice on any good kits to buy and good machine shops to go

to get crank or bore machined. Also what to know what brand of parts are good

to get (pistons, bottom end bearings etc.).

I’m after all the advise I can get please…..

I’m located in Melbourne.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/
Share on other sites

I'd go genuine nissan gasket set/VRS kit, you can get them cheap if you buy from usa same with bearings/rings.

depending on the condition/age of the pistons you may be able to reuse them.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6106287
Share on other sites

Consider buying a short block already completed, you get a warranty and if you buy from a reputable builder you get a guarantee that it is done properly. No risk of someone doing a dodgy job, especially if they have never built an rb before.

rips and redrracing do some fantastic motors all completed ready to go with a warranty.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6107739
Share on other sites

If its affordable I'd base it on a Neo head and matching pistons because I think the later revision has some combustion advantages over the R33 version . I'm not sure what the story is with the CAS here , would the late plastic cover R33 CAS mate the R34 cam drive with R33 engine electrics ?

Also is an RB30 short an option for you ?

A .

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6107846
Share on other sites

Rollz thanks for the comment.... Do u have the contact number or websites for those places that you have suggested?

And thanks to everyone with the help still.... But I would still love more help with website and places to buy good qaulity parts for a build plus any advise on a good machine shop to check and measure bore and crank...

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108087
Share on other sites

Depending on the HP you are targetting.

For reference on my test rig rebuild:

Forged Pistons from:

CJ motors 0421622288

Bearings, head bolds and gasket set from:

MD spares: 95530388

You will need strong valve springs for high boost, I'm using supertech valve spring kit from ebay US.

I Used Reflex engineering for engine rebore, short block building and head reconditioning: 93054807

AMR work shop for assembly: 93866196

That would give a fairly solid "stock engine" but nothing crazy.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108190
Share on other sites

Thanks hypergear for reply.... What area codes are those numbers because I might give them a buzz...

Also with that build what sorta power where u getting???

Thanks alot :)

They all in Melbourne, the area code is 03. The most power I've got of this setup was 345rwkws on 28psi with 98 purple. That was also running stock manifolds and etc. Its used as a test car so it gets flogged on 20psi+ all the time and holding together fine.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108680
Share on other sites

Its a testing rig so it gets new prototypes installed every week. Its currenly running a Ceramic roller bearing G3 which drives pretty nice, the 345rwkws that was a KAI high flow out of a OP6 rear, which made the power but not so good in driving ability.

Cost in building this motor I've spent just under $4G including labor. If your block isn't bad as mine (I had sleeve in 1 cyc) and not looking to beef up its valve springs then you can get every thing done for about $3G.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108775
Share on other sites

Rollz thanks for the comment.... Do u have the contact number or websites for those places that you have suggested?

And thanks to everyone with the help still.... But I would still love more help with website and places to buy good qaulity parts for a build plus any advise on a good machine shop to check and measure bore and crank...

http://www.ripsltd.com/index2.html

paul diemar from red r racing is the other bloke, do a google or search on here, you will find something.

Do it once do it properly imo, the amount of dodgy stories I hear is ridiculous, a lot of people end up doing it twice so you'd be better off just spending the extra the first go and having it done properly. There are lots of other workshops that would do it but being as you are in the USA these are the only two that I know regularly ship overseas. Shipping time will be a while, but I doubt it would be much longer than paying someone to build a motor for you.

If its affordable I'd base it on a Neo head and matching pistons because I think the later revision has some combustion advantages over the R33 version . I'm not sure what the story is with the CAS here , would the late plastic cover R33 CAS mate the R34 cam drive with R33 engine electrics ?

Also is an RB30 short an option for you ?

A .

Need to use the R34 CAS with R34 head, but you just rewire the pins 1-4 2-3 3-2 4-1 and it works fine, same deal with the different coils, you just cut the ignitor out of the loom and it runs fine.

Edited by Rolls
Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6109106
Share on other sites

Was the machining expensive?

What about ur crank? Did u keep stock rb25det crank? If so did u have to get it machined?

Thanks alot with ur replays hypergear :)

I had one badly damaged bore, which had to be sleeved. other wise its only $40 per bore, the crank wasn't bad so they just linished it and assembled every thing together. If your engine's not bad with you doing most of the work the machine part is pretty cheap. Ring up reflex and get a quote. tell them you are from blah blah workshop and they give you a trade discount. How ever bring them the engine block and pistons that are ready to be machined and fitted, they charge alot for stripping the engine.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6109197
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...