Jump to content
SAU Community

Recommended Posts

Hi I’m after some help as my r33 gtst s2 rb25det needs arebuild.

I’m after advice on any good kits to buy and good machine shops to go

to get crank or bore machined. Also what to know what brand of parts are good

to get (pistons, bottom end bearings etc.).

I’m after all the advise I can get please…..

I’m located in Melbourne.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/
Share on other sites

I'd go genuine nissan gasket set/VRS kit, you can get them cheap if you buy from usa same with bearings/rings.

depending on the condition/age of the pistons you may be able to reuse them.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6106287
Share on other sites

Consider buying a short block already completed, you get a warranty and if you buy from a reputable builder you get a guarantee that it is done properly. No risk of someone doing a dodgy job, especially if they have never built an rb before.

rips and redrracing do some fantastic motors all completed ready to go with a warranty.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6107739
Share on other sites

If its affordable I'd base it on a Neo head and matching pistons because I think the later revision has some combustion advantages over the R33 version . I'm not sure what the story is with the CAS here , would the late plastic cover R33 CAS mate the R34 cam drive with R33 engine electrics ?

Also is an RB30 short an option for you ?

A .

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6107846
Share on other sites

Rollz thanks for the comment.... Do u have the contact number or websites for those places that you have suggested?

And thanks to everyone with the help still.... But I would still love more help with website and places to buy good qaulity parts for a build plus any advise on a good machine shop to check and measure bore and crank...

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108087
Share on other sites

Depending on the HP you are targetting.

For reference on my test rig rebuild:

Forged Pistons from:

CJ motors 0421622288

Bearings, head bolds and gasket set from:

MD spares: 95530388

You will need strong valve springs for high boost, I'm using supertech valve spring kit from ebay US.

I Used Reflex engineering for engine rebore, short block building and head reconditioning: 93054807

AMR work shop for assembly: 93866196

That would give a fairly solid "stock engine" but nothing crazy.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108190
Share on other sites

Thanks hypergear for reply.... What area codes are those numbers because I might give them a buzz...

Also with that build what sorta power where u getting???

Thanks alot :)

They all in Melbourne, the area code is 03. The most power I've got of this setup was 345rwkws on 28psi with 98 purple. That was also running stock manifolds and etc. Its used as a test car so it gets flogged on 20psi+ all the time and holding together fine.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108680
Share on other sites

Its a testing rig so it gets new prototypes installed every week. Its currenly running a Ceramic roller bearing G3 which drives pretty nice, the 345rwkws that was a KAI high flow out of a OP6 rear, which made the power but not so good in driving ability.

Cost in building this motor I've spent just under $4G including labor. If your block isn't bad as mine (I had sleeve in 1 cyc) and not looking to beef up its valve springs then you can get every thing done for about $3G.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108775
Share on other sites

Rollz thanks for the comment.... Do u have the contact number or websites for those places that you have suggested?

And thanks to everyone with the help still.... But I would still love more help with website and places to buy good qaulity parts for a build plus any advise on a good machine shop to check and measure bore and crank...

http://www.ripsltd.com/index2.html

paul diemar from red r racing is the other bloke, do a google or search on here, you will find something.

Do it once do it properly imo, the amount of dodgy stories I hear is ridiculous, a lot of people end up doing it twice so you'd be better off just spending the extra the first go and having it done properly. There are lots of other workshops that would do it but being as you are in the USA these are the only two that I know regularly ship overseas. Shipping time will be a while, but I doubt it would be much longer than paying someone to build a motor for you.

If its affordable I'd base it on a Neo head and matching pistons because I think the later revision has some combustion advantages over the R33 version . I'm not sure what the story is with the CAS here , would the late plastic cover R33 CAS mate the R34 cam drive with R33 engine electrics ?

Also is an RB30 short an option for you ?

A .

Need to use the R34 CAS with R34 head, but you just rewire the pins 1-4 2-3 3-2 4-1 and it works fine, same deal with the different coils, you just cut the ignitor out of the loom and it runs fine.

Edited by Rolls
Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6109106
Share on other sites

Was the machining expensive?

What about ur crank? Did u keep stock rb25det crank? If so did u have to get it machined?

Thanks alot with ur replays hypergear :)

I had one badly damaged bore, which had to be sleeved. other wise its only $40 per bore, the crank wasn't bad so they just linished it and assembled every thing together. If your engine's not bad with you doing most of the work the machine part is pretty cheap. Ring up reflex and get a quote. tell them you are from blah blah workshop and they give you a trade discount. How ever bring them the engine block and pistons that are ready to be machined and fitted, they charge alot for stripping the engine.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6109197
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...