Jump to content
SAU Community

Recommended Posts

Hi I’m after some help as my r33 gtst s2 rb25det needs arebuild.

I’m after advice on any good kits to buy and good machine shops to go

to get crank or bore machined. Also what to know what brand of parts are good

to get (pistons, bottom end bearings etc.).

I’m after all the advise I can get please…..

I’m located in Melbourne.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/
Share on other sites

I'd go genuine nissan gasket set/VRS kit, you can get them cheap if you buy from usa same with bearings/rings.

depending on the condition/age of the pistons you may be able to reuse them.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6106287
Share on other sites

Consider buying a short block already completed, you get a warranty and if you buy from a reputable builder you get a guarantee that it is done properly. No risk of someone doing a dodgy job, especially if they have never built an rb before.

rips and redrracing do some fantastic motors all completed ready to go with a warranty.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6107739
Share on other sites

If its affordable I'd base it on a Neo head and matching pistons because I think the later revision has some combustion advantages over the R33 version . I'm not sure what the story is with the CAS here , would the late plastic cover R33 CAS mate the R34 cam drive with R33 engine electrics ?

Also is an RB30 short an option for you ?

A .

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6107846
Share on other sites

Rollz thanks for the comment.... Do u have the contact number or websites for those places that you have suggested?

And thanks to everyone with the help still.... But I would still love more help with website and places to buy good qaulity parts for a build plus any advise on a good machine shop to check and measure bore and crank...

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108087
Share on other sites

Depending on the HP you are targetting.

For reference on my test rig rebuild:

Forged Pistons from:

CJ motors 0421622288

Bearings, head bolds and gasket set from:

MD spares: 95530388

You will need strong valve springs for high boost, I'm using supertech valve spring kit from ebay US.

I Used Reflex engineering for engine rebore, short block building and head reconditioning: 93054807

AMR work shop for assembly: 93866196

That would give a fairly solid "stock engine" but nothing crazy.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108190
Share on other sites

Thanks hypergear for reply.... What area codes are those numbers because I might give them a buzz...

Also with that build what sorta power where u getting???

Thanks alot :)

They all in Melbourne, the area code is 03. The most power I've got of this setup was 345rwkws on 28psi with 98 purple. That was also running stock manifolds and etc. Its used as a test car so it gets flogged on 20psi+ all the time and holding together fine.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108680
Share on other sites

Its a testing rig so it gets new prototypes installed every week. Its currenly running a Ceramic roller bearing G3 which drives pretty nice, the 345rwkws that was a KAI high flow out of a OP6 rear, which made the power but not so good in driving ability.

Cost in building this motor I've spent just under $4G including labor. If your block isn't bad as mine (I had sleeve in 1 cyc) and not looking to beef up its valve springs then you can get every thing done for about $3G.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6108775
Share on other sites

Rollz thanks for the comment.... Do u have the contact number or websites for those places that you have suggested?

And thanks to everyone with the help still.... But I would still love more help with website and places to buy good qaulity parts for a build plus any advise on a good machine shop to check and measure bore and crank...

http://www.ripsltd.com/index2.html

paul diemar from red r racing is the other bloke, do a google or search on here, you will find something.

Do it once do it properly imo, the amount of dodgy stories I hear is ridiculous, a lot of people end up doing it twice so you'd be better off just spending the extra the first go and having it done properly. There are lots of other workshops that would do it but being as you are in the USA these are the only two that I know regularly ship overseas. Shipping time will be a while, but I doubt it would be much longer than paying someone to build a motor for you.

If its affordable I'd base it on a Neo head and matching pistons because I think the later revision has some combustion advantages over the R33 version . I'm not sure what the story is with the CAS here , would the late plastic cover R33 CAS mate the R34 cam drive with R33 engine electrics ?

Also is an RB30 short an option for you ?

A .

Need to use the R34 CAS with R34 head, but you just rewire the pins 1-4 2-3 3-2 4-1 and it works fine, same deal with the different coils, you just cut the ignitor out of the loom and it runs fine.

Edited by Rolls
Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6109106
Share on other sites

Was the machining expensive?

What about ur crank? Did u keep stock rb25det crank? If so did u have to get it machined?

Thanks alot with ur replays hypergear :)

I had one badly damaged bore, which had to be sleeved. other wise its only $40 per bore, the crank wasn't bad so they just linished it and assembled every thing together. If your engine's not bad with you doing most of the work the machine part is pretty cheap. Ring up reflex and get a quote. tell them you are from blah blah workshop and they give you a trade discount. How ever bring them the engine block and pistons that are ready to be machined and fitted, they charge alot for stripping the engine.

Link to comment
https://www.sau.com.au/forums/topic/382790-rb25-rebuild/#findComment-6109197
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...