Jump to content
SAU Community

Recommended Posts

Due to me parting out my car I have a lot of carbon products available (I was a bit obsessed!).

A lot of these parts never ended up being fitted and are in brand new condition.

R33 GTST three piece carbon fibre Top Secret diffuser (made with all the custom brackets to fit a GTST)

post-35676-0-13152000-1324982970_thumb.jpg

R33 GTST S2 carbon fibre front indicator/foglight covers - $120

post-35676-0-89518500-1324983143_thumb.jpg

RB26 carbon fibre coilpack cover (brand new)

post-35676-0-84054900-1324982764_thumb.jpg

R33 carbon fibre drift/lip wing/spoiler (brand new)

post-35676-0-36185800-1324984688_thumb.jpg

R33 carbon fibre coupe weathershields/wind deflectors (brand new)

post-35676-0-00507300-1324984671_thumb.jpg

R33 carbon fibre exhaust bumper heatshield (brand new)

post-35676-0-32821700-1324982794_thumb.jpg

I think that is everything for now.

Any questions feel free to ask. Can freight Australia wide.

Cheers

Phil

Link to comment
https://www.sau.com.au/forums/topic/386649-pmr33-carbon-fibre-mega-sale/
Share on other sites

PM me your email address and I will send you a large file I wrote up on how to make it fit for PSI Parts which has heaps of photos.

I made it fit as a one piece instead of a three piece because it fitted the GTST better. The two side pieces are still brand new.

There is a bit of scratch damage on the bottom of the diffuser when I scraped it one time (wanted to kill some one when it happened!) but you can't see it unless you stick your head under the diffuser and they are coloured in black so you don't see them really. Will take photos of the scratches tomorrow.

Well buy it :P

Nah they weren't fitted. Yeah the window design is a bit annoying. Worst is when you have a wet roof and go around a corner and get a litre of water on you!

lol yeah bit of a pain, Im hopefully heading up there soon to get that engine off Rob, I'll see if I can organise a trip down there to pick up some stuff. But sure I'll buy it off you, looks alot easier then fabbing the brackets etc myself lol. Does it scrape much on the road?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...