Jump to content
SAU Community

Sau Nsw Wisemans Ferry Social Cruise Sunday 19Th Feb 2012


Recommended Posts

  • Replies 181
  • Created
  • Last Reply

Top Posters In This Topic

Hey just thought I would let u guys know that EVO-OZ is doing the exact same run on the same day.

They are meeting at Thornleigh Maccas at 9am and departing at 9:30am though.

Maybe if any of u guys wanna check out some Evo's u can get there extra early..

Hey just thought I would let u guys know that EVO-OZ is doing the exact same run on the same day.

They are meeting at Thornleigh Maccas at 9am and departing at 9:30am though.

Maybe if any of u guys wanna check out some Evo's u can get there extra early..

Coincidence, or sabotage?

Hey just thought I would let u guys know that EVO-OZ is doing the exact same run on the same day.

They are meeting at Thornleigh Maccas at 9am and departing at 9:30am though.

Maybe if any of u guys wanna check out some Evo's u can get there extra early..

Sorry guys that was the wrong date....

it was last weekend

I'm keen if ppl from Newcastle-central coast want to meet up somewhere and head down.

hey luke me and a few others are gunna meet at gosford off ramp around 9ish if ya keen

Hey just thought I would let u guys know that EVO-OZ is doing the exact same run on the same day.

Sorry guys that was the wrong date....

it was last weekend

LOL > However, if you are friends with any of them, can you ascertain if the notorious popo-defect-nazi was around?

LOL > However, if you are friends with any of them, can you ascertain if the notorious popo-defect-nazi was around?

Doesn't that guy go to the putty - not wiseman's? Or is he an SAU member in disgiuse?

:ph34r:

For the Richo boys meeting at the base carpark....I won't be there due to work commitments (:rant: ), but you guys can still meet there and go from there :D

For the Richo boys meeting at the base carpark....I won't be there due to work commitments (:rant: ), but you guys can still meet there and go from there :D

:O

What's that?

Was that a cough???

I think you may be coming down with something....

Spewing mate! The old boy and i-self are still gunna be there if ya keen still Luke?

For the Richo boys meeting at the base carpark....I won't be there due to work commitments (:rant: ), but you guys can still meet there and go from there :D




  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...