Jump to content
SAU Community

Recommended Posts

I found and run the test, but unfortunately did not show up anything, does anyone know where the water control valve is, i presume its an electric solenoid type hidden away somewhere??

Climate Control Diagnostics R32 and R33

The climate control has a diagnostic mode.

Enter the diagnostic mode by pressing the OFF button for five seconds within ten seconds of

turning the ignition on.

Sensor check

Sensor check is selected by pressing HOT switch (the red triangle) while in diagnostic mode.

The microcomputer detects whether each sensor input signal is within correct parameters. The

results are displayed on the screen.

If normal, a "20" is displayed.

If abnormal the failed sensor number is displayed. The sensor numbers are as follows:

20 - all is normal

21 - outside air sensor

22 - Inside air sensor

23 - Water temperature sensor

24 - Intake temperature sensor

25 - Sunload sensor (small sensor on the left hand side of the dashboard near the windscreen)

26 - PBR

27 - Refrigerant temperature sensor

This should tell you if any of your sensors are faulty.

Mode door position check

(This is probably not the cause of your problems but it is a nifty self check to play with).

While in Sensor check, depress the HOT button again. This will operate the the mode door

actuator, and checks the whether the position detection switch is operating. Again the results

are displayed on the display.

If normal, a "30" is displayed.

If abnormal the number of the faulty mode is displayed as follows:

30: Normal

31: VENT

32: B/L (Bi level)

34: FOOT

35: DEFROST/FOOT

36: DEFROST

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-62873
Share on other sites

Originally posted by inark

its 1am... but im going outside to have a fiddle with it just cause that looks like fun haha

lol yea i like fiddling at 1 am too...

sorry i cant help u there jethead. i did the test and 25 - Sunload sensor seems to be faulty....bo my question is, what does it do, and is it important???

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-62925
Share on other sites

Originally posted by inark

its 1am... but im going outside to have a fiddle with it just cause that looks like fun haha

You should have got error 25 (Sunload Sensor).

Word of caution, even in shade on a bright sunnny day you can get error 25.

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63194
Share on other sites

Originally posted by skyline33

leon,

I thought you fixed it

errr the guy that sold it 2 me did....but then a few dayz ago it made that sound again.... :) I don't wanna go back 2 him and get it fixed again..u said u know someone that can fix those stuff right? Need some help man

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63498
Share on other sites

yer..it was the gate thingy that heat your windowz when it goez foggy....it wasn't moving properly.....it still workz though, just makez that annoying sound..... And I dunno y but I get hot feet instead of cold feet...heater is on no matter I turn it off :) weird shit....

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63503
Share on other sites

On the righthand side of the gearbox tunnel Adjacent to your left foot is an servo/motor mechanism that sequences the buterflies and water valve via a push/pull cable. This mechanism was stuck, gave a bit of a helping hand and away it went, all is fine now. Fault code 26 then dissapeared, left with Sunload sensor fail but who cares...Ive got heat now..

Can someone tell how to identify/find the Sunload sensor????

Link to comment
https://www.sau.com.au/forums/topic/3883-no-heat/#findComment-63513
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...