Jump to content
SAU Community

Recommended Posts

Hi guys

Need some help/advice with my r33 gtst.

Basicly my AFM's keep dying after few hours of driving. I had 3 pink label afm's put 1 in, it would run good for a few hours then die. Drove from morley to birba lake put the car on the dyno for a run and the car made 220bhp with the car f*king up. Switched the afm again put the car on the dyno and pulled 278bhp. Cars mostly stock basic mods fmic exhaust and 10psi of boost. AFR on first bad run was around 10-10.5. AFR on good run was up around 12, All afms were just standard pink labels.

Link to comment
https://www.sau.com.au/forums/topic/389097-r33-air-flow-meter-problems/
Share on other sites

Are you sure its not a connection or something else?

1 not working - yep

2 not working - you got poor luck.

My experiance is that the either work or they dont (one the car is warm) so even stranger that its ok for a few hours then goes bad. Happy to be corrected on that.

Find someone that has a working unit, try it and if it still happens you know it something else causing the problem.

Cool Story:Personally I have had them stuff up too. It still worked unless u put your foot down and then would read so incorrectly it caused a boost cut, extremely wide range of idles depending on weather or car would be lacking in power for no apparent reason and lurch! Purchased a second hand unit from here.. guess what.. just as faulty. Purchased a unit from JPC, problem solved and never returned.

Fix:

1 - Check your wiring for the AFM is not shorting out or is damaged between your ecu and afm. Run a direct temporary wire (if your ok with wiring) to test this.

2 - Try an AFM with a guarantee that it works!

  • 10 months later...

still COULD be coilpacks, have them bench tested before you rule them out. especially if they're chinese copies, normally splitfires are pretty good though

ive personally had a brand new aftermarket coilpack fail, so it is possilble

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...