Jump to content
SAU Community

Recommended Posts

Sorry I cant make it either Richo.

Got a new Brake Master Cylinder put on today. A bigger, better, larger unit to suit the Brembo's. BM57. (Bigger than 1")

Instead of the BM50 for the Sumitomos (1")

Now I have braking issues - Again :(

Booked in again Wednesday to get it looked at.

Sin

Stocker should work fine with the Brembos. But then so should BM57, what's the issue?

The stocker became spongy when I had the New rotors and Brembo calipers put on. Pedders put the rear calipers on the wrong side therefore the bleed valve was opposite to where it shouldve been and air got stuck. :(. Took it back twice and they didnt work it out. Took it around the corner to ACT brakes and within 1 minute they told me the problem. So they put them on the right sides and up the right way bled, and all good.

Because I put the Bremo's on I bought the BM57 to suit. Today ACT Brakes put it on and I am back to spongy.

When the ehgine isnt on the brake peddel is hard. Turn the engine on and they go instantly spongy.So doesnt appear to be air trapped in system.

So anyway - back to ACT brakes on Wednesday. If they cant resolve within the day I'll get them to put the BM50 on. As it turned out to be very good.

I thought I'd get better stopping with the match of Brembo calipers and the BM57 like the Vspec I and II.

The bigger BM57 will give you slightly shorter pedal travel and a harder pedal so while the stocker will decrease harness and increase travel it shouldn't be excessive or spongy. The movement when you turn the engine on is it 'sponginess' or 'travel' because the booster is getting vacuum?

Edited by Scooby

The booster appears to get vacuum as it should but the sponginess is more than should be.

There should be a point where the pressure increases and then goes fairly hard as the brakes are applied

I dont get to the hard bit and the first half is soft like there is no pressure.

Any ideas ??

The other thing that annoys me is that every brake shop discounts bleeding the ABS without reason - Why is that?

It connects directly to the BMC, it has the capacity to trap air, it's higher than the calipers and higher than anything else in the brake system (except the BMC which is pretty much at the same level), it has bleed valves on top of it !

I'm not a brake specialist BUT i am mechanicaly minded and logical.

The booster appears to get vacuum as it should but the sponginess is more than should be.

There should be a point where the pressure increases and then goes fairly hard as the brakes are applied

I dont get to the hard bit and the first half is soft like there is no pressure.

Any ideas ??

The other thing that annoys me is that every brake shop discounts bleeding the ABS without reason - Why is that?

It connects directly to the BMC, it has the capacity to trap air, it's higher than the calipers and higher than anything else in the brake system (except the BMC which is pretty much at the same level), it has bleed valves on top of it !

I'm not a brake specialist BUT i am mechanicaly minded and logical.

Faulty valve or torn diaphragm?

  • 1 month later...

So how many of you keen to go for a drive this comming weekend ??

Thinking of grabbing a big breaky in Cooma (1hr away) then maybe a short stop at Jindy for photo op and then lunch at Charlottes private parts.

Maybe even cold drinks when we get back

Following weekend is Wheels @ old parly house.

I won't do it this weekend, doing Motorkhana on Sunday.

But I was close to driving out that way last weekend (Canberra long weekend) until the R32 engine died while out and about. Anyway that got me wondering if any of the roads up there had been closed from the recent rain? A majority of the fun roads were closed and we found out for good reason.

Ahh man would be keen! But I'm getting my St pats day celebrations on.. come on St pat's day on a Saturday! Its like a lunar eclipse...

But next few weekends ill be available. Ill also be getting new rims which will need a photo shoot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...