Jump to content
SAU Community

Recommended Posts

Skyline R33 Rear Seat Removal Pictorial Guide

You should see something like this with an obvious bolt on either side just below the base:

RSR1.jpg

Do this to both sides:

RSR2.jpg

The next step is the only tricky part. You have to pull the base of the seat up and out first, and on either side there is a metal loop stuck in a plastic type catch to hold the seat in place. One side at a time, you'll need to pull pretty much straight up around the area shown in red below. (The catch you're trying to prise free is seen below in blue). This can be hard to remove, in my experience you have to pull quite hard. You can push the middle seatbelt and buckles through the seat first to make things easier.

RSR3.jpg

You should now see something like this. Removal of the backrest is straightforward, just remove the bolt/screw on either side, slide the seatbelts on either side out of the way and then lift upwards and forwards.

RSR4.jpg

You just need to lift over the three hooks shown in red below. Remember to sit the backrest back up on these supports when you put things back in place.

RSR5.jpg

The quality back seats look something like this!

RSR6.jpg

http://users.tpg.com.au/johnkg/skyline/rea...eats/index.html

John

Link to comment
https://www.sau.com.au/forums/topic/39133-r33-rear-seat-removal/
Share on other sites

Good thing, except that on my '98 R33 there are two 'prongs' that go through the floorpan and are released underneath the car by undoing a clamp and squeezing the 'prongs' together then pushing them back up through the hole. These 'prongs' are accessed from under the car ie they are outside the car. I haven't done it yet, tried to get my rear seat out but put the base out in the too hard basket. I only wanted to get my backrest part out anyway, and with a bit of patience it came without the need to take the base out.

PS you can actually see the holes for the 'prongs' in your photo, you have circled them in blue.

Very nice guide!!

I pulled as hard as i could to get the seats out after i undid the bolts... no luck

so i managed (akwardly) to undo the bolts on back part of the seat without taking the bottom part out - was a biatch tho

Good thing, except that on my '98 R33 there are two 'prongs' that go through the floorpan and are released underneath the car by undoing a clamp and squeezing the 'prongs' together then pushing them back up through the hole.  These 'prongs' are accessed from under the car ie they are outside the car.  I haven't done it yet, tried to get my rear seat out but put the base out in the too hard basket.  I only wanted to get my backrest part out anyway, and with a bit of patience it came without the need to take the base out.

PS you can actually see the holes for the 'prongs' in your photo, you have circled them in blue.

hey tridentt150v, I'm pretty sure the prongs you are talking about is the white plastic bit right? Thats just the mount that holds the metal prongs in the car body - the white plasticy bit should stay in the car and the metal loop bit is what you have to lever out.

  • 3 months later...

Um... i tried to remove my seats today and where you've circled the clips in blue in the third pic...well mine didn't come out quite right on the left side... the platic base that holds the clip also came out... is that bad? :s

Um... i tried to remove my seats today and where you've circled the clips in blue in the third pic...well mine didn't come out quite right on the left side... the platic base that holds the clip also came out... is that bad? :s

Hmmmm! Sounds like you've just written off your car....tough eh!!

On further consideration..you might just save the day if you prise the white base off the steel loop and replace it in the hole with a bit of silicon and an abject apology :wassup:

A better way to remove the seat base...especially if its tight ..is to use a large screwdriver or prybar just inside of the black bracket and lever it up

thanks 51jay but i meant from a safety point of view. :) sounds like no biggy. Still, couldn't get the seats out so thought screw it and gave up. Will do it later when i have an urgent need to. I only really wanted to get at the base of the back windscreen cause the guy who removed the tint did a crappy job and left glue all over the window.

  • 11 months later...
  • 2 weeks later...

Hey nice guide. I've tried taking out the rear seats previously along with a few of my mates and we failed. We got stuck at the same point everyone else seems to, but now i know it will eventually come out ill have another go at it. I think ill just get some leverage or muscle power and lift the front of the seat up until something breaks or it comes out lol.

  • 1 month later...

FOR EVERYONE:

Even easier than pulling it up by yourself and taking a while and all that strength....... is to jam a crowbar under each side and pull up, its out in two seconds!......trust me it's easier hehe

Edited by NeesaanGTS
  • 11 months later...

Don't need piccies!

Bottom of rear seat has two bolts, on the side of the footwells, can't miss them)

Push the bottom-seat down around the seatbelt area, and you'll see a bolt on each side holding the back-seat in. Undo those.

Back-seat goes up to unhook, bottom seat goes forwards and up (it's hooked to the back-seat)

  • 4 months later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...