Jump to content
SAU Community

Group Buy, New R33 Front bar.


Recommended Posts

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

I am very interested, but would like to see a picture of it on a car to be sure.

Dont take this the wrong way, but what is the quality of the bar like? My car is beeing painted by one of the top (most fussy) painters in SA, and if it dose not sit in correctly, or isnt straight he wont touch it. (dont want to waste your time and money shipping it back to you)

I am going to pair it up with an impule bodykit, but I am unable to get a front bar at the moment (nor for the forseeable future), hence the need to look at alternatives.

PS what would it cost to ship it to Adelaide? (in the next week (2 weeks at the most))

Guest MFX_R33

My car is in pieces at the moment (and has been for 8months) and wedged in a corner, so you wouldn't see much.

As for the aero dynamics, the bar is designed to give a good amount of front downforce, and is also designed to go with the carbon fibre cannards we are currently finishing off.

The bar is also designed around a 600x300 intercooler, so you can receive maximum flow.

Jeff.

i just wanted to know where u tested its aerodynamics. as to do this properly you would need to put it on a car then put it thru a wind tunnel you would also have to put the original car in a wind tunnel to see the differences in downfoce. Only monash clayton has these facilities in australia. the wind tunnel their goes to 200 km/hr. and its very expensive to hire...

i just wanted to know where u tested its aerodynamics. as to do this properly you would need to put it on a car then put it thru a wind tunnel you would also have to put the original car in a wind tunnel to see the differences in downfoce. Only monash clayton has these facilities in australia. the wind tunnel their goes to 200 km/hr. and its very expensive to hire...

dont want to start a nerd-fight in someone elses thread - but you sir, are a goon!

Guest MFX_R33

No we have not tested the bar for exact aero dynamic properties. As I said we have "designed" it to give a greater amount of front down force, using the wing shapes on either side of the bar, and as I mentioned before, with the optional carbon fibre canards.

If someone on here wants to know the drag coefficeint of the car before and after the kit, they would be hard pressed to find it for any kit. This factor will also change for most cars at any rate, as it depends on may other factors as well, including ride height, and the other aero parts they have fitted to their car.

This said, most people buy body kits for purely cosmetic reasons. We are offering an alternative to the limited range of R33 kits available in Australia. There are very few companies in Australia producing NEW stuff. If you like it that's good, if you don't that's fine too. We are just offering you guy's another choice.

Jeff.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...