Jump to content
SAU Community

Recommended Posts

Do you have a clip of what the Blitz BOV's sound like if possible? Or can find one of the specific Bov's?

Thanks

It's like this one. That's not me in the video explaining it though so don't ask for a translation.

Sump is now sold.

These items are still available.

Rb26 crank out of an r32. Good condition and will supply a crank collar that the buyer can put on. $450

2 x standard turbos, with wastegates and dumps. Very minimal shaft play. $350

Standard rods/pistons, good condition. $200

Radiator Fan with clutch, all fins in good condition $90

6 x standard injectors $200

Standard ecu $95

2 x air filters, unknown brand. They have never been used and have the adapters to bolt to the afms attached. They are fairly large (around 4inch diam) and are made of chromed plastic. $40 for both.

2 x blitz blow off valves still attached to pipe $220

Front timing cover. In original black paint and in good condition, $80

2 x standard afms, great condition with plugs and mesh still intact. $200 for both

Standard power steering pump $100

No cracks in the fan. I am located in Melbourne (northern subs).

Someone else has expressed interest in the fan so it is 'sold pending payment'. Will update if sale falls through.

These items are still available.

Rb26 crank out of an r32. Good condition and will supply a crank collar that the buyer can put on. $450

2 x standard turbos, with wastegates and dumps. Very minimal shaft play. $350

Standard rods/pistons, good condition. $200

Standard ecu $95

2 x air filters, unknown brand. They have never been used and have the adapters to bolt to the afms attached. They are fairly large (around 4inch diam) and are made of chromed plastic. $40 for both.

2 x blitz blow off valves still attached to pipe $220

Front timing cover. In original black paint and in good condition, $80

2 x standard afms, great condition with plugs and mesh still intact. $200 for both

Standard power steering pump $100

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...