Jump to content
SAU Community

Recommended Posts

Time has come to move this car on. I have a GTR sitting at the oldies I want to bring home. Bought the car in start of 08 and with plans to make it a nice streeet car with a bit more power. 4 years on and the car sits in the garage and is only driven to shops and back and occasional weekend to friends place, etc. Only done 5-6000 klms since iI bought it. Have some Mods which was going to be installed when I got a turbo, etc toall go on together, just house reno's coming first.

All parts will be sold with the car or can look at removing some parts to lower the price upon negotiations

Standard Info:

1999 R34 GTT

White, Coupe

Manual

Original ODOmeter reads 58, xxx klms, Have installed Series 2 ODOmeter with Carbon Fiber surround with 74, xxx klms and have travelled around 500-600klms on it

Rego till November 2012

LOCATED in Windaroo 4207 (near Beenleigh)

Contact: 0438 88 68 93

Interior:

Nismo Key

Leatherette Seat Trims - Black & White with GT logo (see pics)

Leather Center console lid, Gear boot & handbrake boot

Series 2 ODOmeter

White Globes (Center lights & map lights)

Impul Pedals

Aftermarket Boost, Oil Temp, AFR guages - AFR sensor wire not installed to O2 sensor yet

Exterior:

Do-Luck Front bar

Bomex sides & Rear Bar

Blitz/URAS Front Qtr Panels with Vents

LED Tail Lights (Bought from Just Jap)

LED Boot Brake Light

Clear Side Indicators

Also have LED panels to make the reverse lights bright white but not installed

Wheels are Gram Light 57C's 8.5 Front / 9.5 Rear

Rear tyres have almost new Federal RSR Semi Slicks 255/40/17 with 90-95% tread on them

Engine & Brakes:

Power FC - Have original ECU to go with the car also

Yellow Jacket Coilpacks

Blitz ID3 Boost controller & Powermeter URAS Limited Edition - Not installed

3 inch Cat back with cannon

High Flow Cat - Not installed Brand New from Just Jap

3 inch Split Dump Front Pipe with flexi pipe - Brand new never installed

O2 Sensor - Brnad new sitting in the new dump/front pipe

Greddy FMIC

40mm Aluminium Radiator - Cooling system was flushed when installed and filled with Redline Coolant with 20% antifreeze

Tein Coilovers

Alarm/Immobilizer with built in Turbo Timer

DBA Slotted Front & Rear rotors - Brand new not installed

Braided Brake Lines - Brand New not installed

Braided Clutch Line - Brand new not installed

Magnetic Oil Plug from PMR33's group buy

Apexi POD with S/Steel pipe to Z32 AFM with plug - Brand new never installed

Hopefully havent forgotten anything but can check out the car yourself if interested.

Price is $16,000

Pics below

Link to comment
https://www.sau.com.au/forums/topic/394906-fs-r34-gtt-qld/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...