Jump to content
SAU Community

Recommended Posts

Hi,

I feel very stupid as heading states I hooked up fuel lines wrong way round. Just put my rb26 in my car and connected them up not thinking just so fuel didnt drip everywhere and to get them out of the way.

I hooked up wiring and fuel pump and starter, I just wanted to turn it over after rebuild, turned key to accessory and fuel pump started. meanwhile i could hear a strange pressure building noise and quickly switched it off.

very soon after i realised that fuel pressure had built and obviously couldnt get past the fuel reg and fuel passed through the injectors into the cylinders.

Q 1. are my injectors going to be okay after that sort of abuse.?

Q 2. is my fuel reg going to be okay?

Q 3. will this effect run in and the hone job on the bores or the rings themselves? (Fuel was pushed out of cylindars within half an hour.)

Q 4. Will I not know any of the above until I test each thing.

Thanks

Taylor.

I don't understand, I hooked mine up the wrong way as well once and fuel just didn't get past the reg, so how has it got into your cylinders ?

fuel shouldn't get past the reg the wrong way and pump should turn off once pressurized

I assume it pressurised the injectors so much they leaked out the tip. fuel got into the cylinders through the injector tip. fuel pump didnt switch off once pressurised it just kept pumping and filled the cylinders in seconds

on an rb26 the rails pressure reg is on the front of the rail itself before the injectors. the lines were reversed so the fuel went to all of the injectors first and stopped at the reg at the end and i assume couldnt get past the reg

Reg is definitely on return side cause it needs to regulate pressure in the rail..

so sounds like it is hooked up the right way..

So either your pump isn't switching itself off once pressurized, have your rewired it lately?

Or your injectors are stuck open for some reason..

maybe your injectors are getting voltage I dont know why this would happen

I had 90psi fuel pressure on mine and it wasn't enough to push injectors open, then again my pump would switch off..

Fuel can't get past the reg and even if it does you won't have much pressure in the rail because there is nothing to stop it running back to the tank.

The reg restricts flow back to the thank to increase pressure in the rail.

Your injectors, reg and engine will be fine.

If you're really scared and want to be sure pull the spark plugs out and crank the engine over with the cam angle sensor disconnected to clear out any fuel in the bores.

Id say more then getting the line's the wrong way you have leaking injector seals? Or the reg jammed shut over pressurising the rail causing fuel to leak past the injectors?

Everything would now have been washed of any oil on its surface. Id drain everything, leak everything open for a few days to let any fuel evaporate out then refill with oil, then crank it by hand for a while?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Greg speaks wisdom. These dirty old Datsuns are only value when they are cheap. When they are not cheap, there is no value. Sounds contradictory, but it's true. We are now 20 years past the hey day of modifying cheap 90s JDM cars for small amounts of money. This is a different world. If you are rich and can afford not to care about what is effectively wasting money on an old Datto shitter, then I have no reason to argue against it. But if you are wanting to experience what we all experienced back in 2005 (and I bought my car last century!) then there is no way to do it.
    • Short answer: No. Medium answer: No, because you still need to conjure the things out of thin air to bolt them to a NA to make it a NA+T. Long Answer: No - The things you need to conjure - meaning a turbo, intercooling, manifolds, exhaust, intake/manifold/piping, clutch, injectors, fuel pump, AFM (?), ECU + Wiring (woo, N/A loom fun) have to come from somewhere. You could have many scavenged these things from an OEM car that someone had upgraded from and use some of these. This will be cost prohibitive now, especially so in the USA. You'd probably pay the same for newer, upgraded components that are better than old OEM stuff from 25-30 years ago. None of these big ticket items are re-usable for the N/A car. Why not buy new and upgrade while you're there? The only real consideration is turbo and fuel sizing and determining whether you want to stay within the bounds of the OEM engine or get into rebuild territory. These limits ARE lower with a N/A motor and especially N/A gearbox at the starting point. And if you're gonna upgrade those then you may as well consider having them built to begin with. Because everyone here knows you're never far from that next engine rebuild once you start making the power you want... The cars you see on the internet and SAU etc have been built over decades. If you're really clued in... you would sell your US car to somebody for what you paid for it. You would then scour AU JDM pages or SAU and buy a car like Dose's on this forum with your powerful American Dollar. This will save you so much money in the long term. Importing it could be tricky. Or it might not because USA. I have long said the only reason 90's Japanese stuff took off was because a) Japanese people had Japanese cars so that is what they used b) Australians could import these cars to Australia with very minimal changes and use them on the road here c) Neither country had well-priced access to US or EU Sports Cars. I don't believe the JDM scene would have taken off in Australia at all if we had EU priced EU BMW M offerings, or more especially the AUS V8 Scene would never have existed if we had the multitude of US cars like Camaros, Mustangs, Corvettes at the prices you folks do. After all - Do the math. I would say put a V8 in your R34 and that's the smart way forward. It is. I did it. I know this from my own experience. But at that point there's no reason to simply not buy a C5 or C6? It would be simpler and easier and cheaper and bette-
    • Reading all this... hurts lol. I have an ENR34 5MT and I paid an inflated USA price for the car alone, had to do tons of preventative maintenance past that, and so I'm over $30K USD into the car already and haven't even touched power.  I wanted to +t it. Not even trying to make GTR numbers, I'd be happy with 250hp.  Can I get away with paying much less to make that happen?
    • Damn you’ve done well, definitely snapping necks.
    • Great weekend and event. Open fire at the caravan park, perfect weather all day and a great feed and a couple of drinks at at awesome country pub.
×
×
  • Create New...