Jump to content
SAU Community

Recommended Posts

Hey.. Just wondering if anyones got any thoughts on a possible cause of car shuddering when braking under heavy conditions, like brakeing from above 100k's. Had new pads front and rear and discs machined and checked for warpage, came up good but still shuddering... Any ideas? Car is a series 2 c34, RB25det auto.

Link to comment
https://www.sau.com.au/forums/topic/396583-car-shudders-when-braking/
Share on other sites

Does it do do it when the brakes are cold too? Brake discs, especially the front can get heat spots in the rotors that are un-machineable. Other than that i would be checking my wheels bolts and front hub nuts mate :thumbsup:

bearing and ballance nd hub nuts would all cause vibration even when not braking. it would be something brakes. maybe double check caliper bolts if they left any lose, otherwise would be warped rotors. so were not machined properly most likely or have warped since then. have u been through puddles of water after a long or heavy drive? check for discolouration in rotors (ie heat spots)

Thanks guys. Have checked bolts and all that in the past and all checked out good, i will re check though i think. I did have a problem with my lhr caliper, it wore the pads down passed the metal backing, while the rh side was fine and i never fixed that i just bought new pads. That wad only the rear though which would only affect the brake pedal and not the entire car right?

that is right. rears will shudder pedal. nd to fix that wearing problem, remove nd put caliper slide grease on the slide. as slide could be seized. for steering shudder it will be in the fronts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...