Jump to content
SAU Community

Recommended Posts

It is a piece of cake.

A few tips:

- if you brake fluid is very full in the reservoir, remove some, as when you squeeze open the brake pads to put on the new/wider disks, fluid gets forced back into the reservior and will overflow if it is too full (I did this when I recently changed pads).

- open the brake bleed nipples to make squeezing the pads open easier, but once disks are fitted you should bleed them again anyway.

- buy braided brake lines (cheap = $200-$300) and put them on while you have it all apart.

Nope - never worked on handbrake shoes.

You can pull out the rubber grommet to get access to the rear hand brake adjusters and back them off a bit. But when I did mine last year the backing plate was held to the rotor by rust etc so you need to give the centre of the rotors a few hits with a club hammer to loosen same. I had to be quite brutal to free it up. It isnt particularly difficult other than for loosening the rear rotors.

  • 3 weeks later...

I'm putting DBA slotted Rotors all round On a factory 250GT (I presume sedans have same brakes as a 350Z touring yeah), braided brake lines and new brake pads

(can anyone reccomend some good ones), having my handbrake tightened while my coilovers are being put in..... Within the coming month

I'm putting DBA slotted Rotors all round On a factory 250GT (I presume sedans have same brakes as a 350Z touring yeah), braided brake lines and new brake pads

(can anyone reccomend some good ones), having my handbrake tightened while my coilovers are being put in..... Within the coming month

my previous experience with dba slotted rotors and bendix blue pads was not a good one... downhill braking resulted in smoking brakes, and pedal touching the floor. the pads when heated up literally had a chatter feel similar to dragging a wet washing glove on a plate

Edited by Deep Dish V35
  • 3 months later...

Bringing this thread alive again -

My rotors are showing wear, with visable lines on the face and discouloring. My brakes also squeel a lot in the cold or after rain in the morning when i first start driving.

I have had a bit of a look into Stoptech rotors and they seem to be reasonably priced, but if i'm upgrading rotors do i need to upgrade the capiler and pads too? I've got Brembo's 03 coupe.

No, although it would be best to do pads at the same time.

Just make sure that the rotors are for your brake package (ie 350z Track)

Thanks for the advice mate,

I have heard off my mate with a Supra to stay away from drilled rotors because they get really hot. Is this true? Would slotted Stoptechs fit in my wheels, i am about to buy a set of 20's.

Thanks for the advice mate,

I have heard off my mate with a Supra to stay away from drilled rotors because they get really hot. Is this true? Would slotted Stoptechs fit in my wheels, i am about to buy a set of 20's.

Drilled rotors don't get any "hotter" than a normal rotor, that's a function of how hard you use the brakes.

The drilled holes become a stress riser due to localised heat and expansion & contraction of the rotor.

Just get some slotted ones; they still de gas the pad, and deglaze the rotor, that's where the benefit lies.

Brand is irrelevant, you have to buy rotors that have exactly the same dimensions as what you are running now; otherwise the caliper won't fit on.

The wheels not fitting will be the least of your worries.

I don't mean to offend.

With some of the basic questions you're asking; it might be better if you leave it to a professional, or at very least, have an experienced mate assist you with it the first time.

Brakes are not something you can afford to get even a little bit wrong.

Edited by Daleo

Drilled rotors don't get any "hotter" than a normal rotor, that's a function of how hard you use the brakes.

The drilled holes become a stress riser due to localised heat and expansion & contraction of the rotor.

Just get some slotted ones; they still de gas the pad, and deglaze the rotor, that's where the benefit lies.

Brand is irrelevant, you have to buy rotors that have exactly the same dimensions as what you are running now; otherwise the caliper won't fit on.

The wheels not fitting will be the least of your worries.

I don't mean to offend.

With some of the basic questions you're asking; it might be better if you leave it to a professional, or at very least, have an experienced mate assist you with it the first time.

Brakes are not something you can afford to get even a little bit wrong.

Excellent, thank you for that i understand it now. I will have to look up my dimensions then and go from there. No offence taken at all, i asked the question and requested information and that's what you guys are doing for me so i appreciate it. I just wanted a bit of an idea what to go with for now, my brakes will be fine for months to come so i'm not going to worry about it asap as i have money going on different things but i will keep this info in mind.

Of course, i would not try to fit them myself my Dad was a mechanic for 30 something years so i can always turn to him if i need something put on.

Best to get 2 piece floating rotors like I have - when the disk gets hot it expands and contracts independent of the rotor centre, eliminating the chance of disk warping.

Floating rotors aren't exactly a guarantee against warping, although the better quality base materials of a 2 piece rotor would certainly help.

The main reason for using 2 piece rotors (in my understanding) is that in high load conditions (i.e; trackwork) the alloy hat minimises the heat of the rotor transferring into the hub; and overheating the bearings causing a failure.

Excellent, thank you for that i understand it now. I will have to look up my dimensions then and go from there. No offence taken at all, i asked the question and requested information and that's what you guys are doing for me so i appreciate it. I just wanted a bit of an idea what to go with for now, my brakes will be fine for months to come so i'm not going to worry about it asap as i have money going on different things but i will keep this info in mind.

Of course, i would not try to fit them myself my Dad was a mechanic for 30 something years so i can always turn to him if i need something put on.

Good stuff, best of luck. :thumbsup:

Edited by Daleo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...