Jump to content
SAU Community

Recommended Posts

Hey Guys

Need some advice

Long story short, a guy reversed into my parked car, caused pretty major damage on the front end bumper.

Have a witness who wrote a note and put it on my car with details of number plate and he has photos he will email to me.

I park in front of a client i work for on Tuesdays and i being in IT i went through the CCTV footage and low and behold, i got it on camera.

Car hit my car, pushed my car about 30 cm then drove off ........

Now....the crap part....i dont have insurance on my car (r34)....( stupid i know but i cant afford it :(....)

Every is saying file police report, now i have done that and they are comming back saying it has to be over 800 dollars worth of damage for them to proceed.

Anyone have any idea if its worth proceeding ie would it be over 800 to replace a front bumper + fitting , the bumper cant be repaired as far as i can see....unless they use a shit load of fibreglass....

and if i do go get a qoute, who do i goto, im north of the river.

Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/396820-hit-and-run-help/
Share on other sites

if he hit you that hard and drove off and your fiberglass bumper is cracked then your reinforment bar might also be damaged hense it would also need replacing. If thats the case then it will most likely be 800 or a bit over including labour costs =) some panel beaters charge an arm and a leg for repairs just go to a few trusted panel guys and get a few quotes.

Btw as far as i know you dont need insurance the guy who hit you does as he will be repairing your car and his insurance will be paying for the damages!

Edited by DarkRyda

Any light or grill damage?Factory front bar from nissan + reo bar from nissan + fit and paint is going to be over $1k.

If you get it patched up you probably wont hit the $800 mark so aim for new replacement parts.

Just take the car to a couple of panel and paint shops, they will be more than happy enough to give you a quote.

Any light or grill damage?Factory front bar from nissan + reo bar from nissan + fit and paint is going to be over $1k.

If you get it patched up you probably wont hit the $800 mark so aim for new replacement parts.

Just take the car to a couple of panel and paint shops, they will be more than happy enough to give you a quote.

Its not a factory front bar, its a custom bar of some sort ( never seen what it looks like before, but its ugly :P ).

Whats a place that rips you off north of the river lol?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...