Jump to content
SAU Community

Recommended Posts

Car is up for expressions of interest

Its a 1995 R33 GTS RB25de Manual with 143,063km on the clock.

Plenty of work has been done and everything is in good condition. I have the original import papers, recipts for most of the purchaces and modifications done to the car. This car has been very well looked after by myself over the last 2 years. Ive only put 98 fuel into it and have serviced it every 5,000km

Will put some pictures up in the coming few days.

Read and look at some pictures and video footage in this build thread.

http://www.skylinesaustralia.com/forums/topic/348709-r33-gts-build/

Car is located in Brisbane QLD

EOI: 10k

Interior

Sparco chrome pedals

Blue ac/speedo lights

Auto meter 3 Gauge cluster - a/f ratio, Oil/water temp

Nismo shifter

Cusco roll cage sprayed flat black

Replica bride low max

Engine Bay

Apexi pod filter

Custom aluminum intake piping

Custom CAI

Full exhaust system - DK&E extractors, 150 cell high flow cat, 2.5" piping, Varex cannon muffler

Apexi strut bar

Custom hand brake and shifter boots

NPC Exedy heavy duty clutch - 125,417 - Oil change

Clutch master cylinder rebuild - 128,000

PWR 21 row oil cooler

Oil filter relocation kit + cooler lines

Platnium spark plugs

Exterior

Nismo clear side indicators

Black Driftek rims 17x8 +34

Blue lock nuts

6000k HID lights

Series 2 rear spoiler

s2 front grill

White parker lights and licence plate

Mspec front bar

Guards rolled professionally (no hammers)

Other

GTS-T rear sway bar

GTR adjustable rear strut bar

RDA Front and back slotted rotors - 123,000

A1RN QFM brake pads front and back - 123,000

Hel braided brake lines (blue) - 123,000

5 stud R33 GTS-T - 123,000

R33 GTST 4 pot calipers 2 pot back

Diff re-shim - 127,000 - Penrite Limited Slip diff fluid

Bosch battery

Adjustable arms

- Front Caster

- Rear Toe

- Rear Camber

Tein RE coilovers - DQNo5-1CBC2 - ECR33-R-1001

Federal 235/45/17 595 SS

Brand new rear hub bearings

Personialised plates: 33FTW

Bad points on the car would have to be a few body imperfections. Having a small bit of rust around the bottom left rear windscreen and along the middle right of the windscreen as well. Im guessing from a crappy install by a previous owner.

Car has an exhaust defect on it at the moment which I am sorting out before sale. Will be adding an extra muffler to the system to quieten it down.

Feel free to ask any questions. I only want genuine buyers.

Regretful sale but I must due to a change in living conditions.

0434813979 - Joel

  • 2 weeks later...

Added an extra hotdog resonator to the exhaust system today which has quietened it down a bit and has a very nice note to it.

Car is also fully mod plated for everything that has been done to it so no need to worry about legality's P PLATE friendly.

Hmmm interesting project..

For all the gravel heads like me, the R33 GTS is actually homologated with CAMS, so you can legally rally this thing as a PRC rally car. Would be sweet to have a 9000RPM RB throwing rocks in the forest. Just need to pull out another 2-300kg, and work out how to fit 15" rims over the brakes, and a rallying we will go :yes:

I presume the cage is bolt in? Does it have harnesses?

I did get it down to 1230kg before the cage (if I remember correctly) Yes the cage is bolt in, I haven't got any pictures with it in but I will put some up later on. Have always been meaning to get a harness but never got around to it.

  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...