Jump to content
SAU Community

Rb20Det Converted To Na.

skyline32sup
 Share

Recommended Posts

WMDC35 Experienced

WMDC35

Posted
Posted

Sv6 runs what a high 14 standard, a turbo r33 runs a low 14

Your 50hp turbo less r33 will not beat an sv6

So pull the other leg son

This!, I recently sold a VE SV6 & i've many DE daily drivers, unless the sv6 has something big time wrong with it, it will dish you a beating, an exhaust that big on an NA will just be a megaphone

Super Drager Mentor

Super Drager

Posted
Posted

That was just between driving one and drivin mine i will be taking it to wsid in next few weeks and il post pics of time slips

Please do, i'll come and watch.... hell i might even run again.

Jamie86 Newbie

Jamie86

Posted
Posted

Il put up the date I'm going when I figure out work times, I must be very wrong in terms of driving one from the other and I will admit I'm wrong but from what I could remember didn't seem

That much quicker, il put a 0-100 vid up and you can see if it what I think it is or if I'm way off any ideas on what a normal de is?

Jamie86 Newbie

Jamie86

Posted
Posted

Has oil return lines to sump and det on plate so I'm pretty sure it was det

Never put a car down quarter so I have no idea what it would be

Dunno why so many people are so negative I'm

Not out trying to prove its a monster I was just saying it doesn't go as bad as every makes out

Its still ball of fun to drive

Sorry of I upset some people by saying the sv6 thing but that's what I thought

mad082 Grand Master

mad082

Posted
Posted

the main point we are all making is that it will be noticably slower than a factory non turbo skyline, for the simple fact that the engine is running much less compression. so that, and the fact that other people have done this and put it on the dyno and made about the same power as a hyundai excel. however the condition of the engine comes into play a bit. a very healthy DET will have similar compression to a rather unhealthy DE. however an unhealthy DET (that may still seem ok to drive with the turbo still attached) will be well down on compression compared to a healthy DE (to the tune of about 30%)

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...