Jump to content
SAU Community

Recommended Posts

  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

good work Vange .... saw u do the u-turn after - you made a special trip just for me? awwwww

Thx Sean :(

Spotted the 2 cars below today

RX7 = ** Drool **

Range Rover = OUCH!!!

post-669-1146211463.jpg

post-669-1146211475.jpg

ah i was gunna say thats not bad for a phone :( but yes poor for a camera

**edit**

i got the samsung 4mp camera and that too sux for a full zoom in ok for half and 3/4 zoom

Edited by Madaz

nah just getting somthing 2 eat with a 'friend' :P couldnt find ant y good parks near jetty rd lol

actually i did c a few lines drive past as i was eating my yiros..1 would have been u :)

Edited by vange
Im am more than sure I spotted you a couple of days ago on the Reynell rd and Old South rd intersection, you were going the other way up Grant rd, nice exhaust note by the way! Looks like a straight through exhaust out the back! Good luck with the sale !

yea, if yu heard me, then it was more thn likely me!!! bit too loud imo, but sounds tuff when you give it a bit of stick! both cars still 4 sale :D

mark

This arvo on Panatalinga Rd Woodcroft spotted a R30 turbo coupe(red), R31, R32 and 3 R33's all within 20 minutes of each other. Was there a cruise on or something? Seems to be more and more lines around these days. :)

Spotted a silver R34 parked in front of 55 Currie St. this morning at about 11.45am. Very nice body kit. Huge chromy rims! From far, I guess they were about 19-20 inches!! Lowered, FMIC. Sexy looking car. Man...you must have guts to dressed up your car that way. I wouldn't be surprised if you were always late to reach your destination - cause the cops definitely love you!! :(

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...