Jump to content
SAU Community

Recommended Posts

Hi all, im in the process of building an R32 drifter i want around 400-450hp, its currently got RB25 i put in.

MODS

Microtech LT12s

FMIC

3inch exhaust

YellowJacket coil packs

Stock everything else

its making 200kw on 12psi

My plan is the folowing mods

hypergear xIU stock 25 turbo highflow

WMI

Will this come close to that power figure or will i be better off buying a GTX 30/76?

Edited by 51NNA
Link to comment
https://www.sau.com.au/forums/topic/397558-400-450hp-rb25-build-questions/
Share on other sites

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Well you will need bigger injectors, Fuel pump, a little highflow wont make 450hp at the wheels

GTX3076 will be over kill, better off with a GT3076 or if you really want a silly billet wheel then a GTX3071 would be better suited

Assuming you mean 400-450HP at the engine, then yeah, the Hypergear highflow will get you up into that space. But you're likely to need more fuel. I wouldn't rely on the meth in the WMI to provide enough. You're also likely to need to make sure the ignition system will cope.

It does have yellowjacket coil packs, i was hopeing for RWHP and Zebra i wasnt 100% sure on spending the extra 500$ for a billet wheel, but would you go a 71 over a 76? and my injectors are only on 50%duty cycle so hopefully they would cope too atleast 370-400hp with the WMI

Are they standard injectors? If so they will not do 400rwhp, about 300rwhp is the limit at standard rail pressures

WMI should not be used to increase fueling capacity, doesnt work like that

GTX3076 is capable of 500+rwhp on the right fuel nad engine, but slightly laggier than the regular GT3076 which will do just shy of 500rwhp on the right fuel/engine

Well i was hoping too be sneaky and run my AFR at 13 with the wmi protecting against ping, ATM its 199.6rwkw with 53% duty cycle with stock injectors on 12:1 afr

Edited by 51NNA

Its pretty interesting to find that Toshi managed 2x 260rwkws R33 using our stock 21U R33 high flowed turbos on factory injectors pump 98 done on two different dynos. Not sure whats the go there, unless he can flash the stock ECU to run stock injectors at 100% injection or some thing similar.

only with toshi's remaps.

2 results out of hundreds of others doesnt make it a trend imo

Only with toshi's remaps. I remember he stated some where that he can make it do that no worries. I've never seen that done with other tuners.

Well looks like im up for some injectors too lol, 550cc be enough?

OR buy a GT30/76 or GT30/71, WMI and put it back on the dyno and see what happens and go from there, after all spending 1k on injectors i might not need (probly will do) but would be interesting too see what happens?

Edited by 51NNA

most would say 75% injector duty would be the max they would want for safety...

get siemens injectors and a new rail and it will be cheaper than sard or nismo injectors and you can get larger to support E85 and not worry about WMI....

Its pretty interesting to find that Toshi managed 2x 260rwkws R33 using our stock 21U R33 high flowed turbos on factory injectors pump 98 done on two different dynos. Not sure whats the go there, unless he can flash the stock ECU to run stock injectors at 100% injection or some thing similar.

I made 260kw at 15psi so never 100% injector duty.

Injector duty is around 88-92%.(depends on AFR)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...