Jump to content
SAU Community

Double Sided Tape That Sticks?

Ruxis

By Ruxis,
in Exterior & Interior Styling

 Share

Recommended Posts

Ruxis Veteran

Ruxis

Posted
Posted

hey guys,

easy question this time, looking for double sided tape that will actually hold something on (bit of body trim has lifted, gunna refit) unlike the crap you buy from supercheap.

would like it super sticky, thin and not to expensive.

buying online is fine or somewhere in/around newcastle

Jarrad

Link to comment
https://www.sau.com.au/forums/topic/397980-double-sided-tape-that-sticks/
Share on other sites
RusH_ Veteran

RusH_

Posted
Posted

As above 3M double sided tape, has red backing paper. If you want something that isn't going to move pretty much ever try out 3M's VHB 4991 double sided tape (i believe it's what is used to hold the go-pro camera stands etc to cars/boats etc...)

I don't think you can simply get this one from bunnings, but i may be wrong as i get it directly from 3M

gotRICE? Veteran

gotRICE?

Posted
Posted

where's the cheapest place to get it though, ebay, bunnings or online somewhere, anyone got some shop prices for comparison to online?

Its a roll of tape :P Just pay what it costs ya tight prick LOL!! :) :)

So i dont start a new topic.. can anyone tell me if this stuff works on dash boards? EG under the steering column for turbo timers/ gauge control units?

Iv tried so many things, command strips, double sided tape.. HOT GLUE! (this worked the best)

But eventually everything has fallen off. I even cleaned the area with thinners to try get the dash oils away. One way or another it falls off in the heat.

sky017 Proficient

sky017

Posted
Posted

dash boards are always going to be likely to loose the grip of the tape if they are constantly in the sun . thinners are a bit much to clean your dash lol harsh.. try wax and grease remover , thatll be a little more friendly , you wouldnt want any cloth streaks in your dash from thinners :P .

Gibbon138 Enthusiast

Gibbon138

Posted
Posted (edited)

Tried sikaflex? http://www.sika.com....to_products.htm

it's what they use at the factory when they need to hold on bodyparts/trim without screws/bolts/stupid plastic lugs etc.

**edit: good luck EVER getting it off though

Edited by Gibbon138

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I agree with everything else, except (and I'm rethinking this as it wasn't setup how my brain first though) if the sensor is at the end of a hose which is how it has been recommended to isolate it from vibrations, then if that line had a small hole in, I could foresee potentially (not a fluid dynamic specialist) the ability for it to see a lower pressure at the sensor. But thinking through, said sensor was in the actual block, HOWEVER it was also the sensor itself that broke, so oil pressure may not have been fully reaching the sensor still. So I'm still in my same theory.   However, I 100% would be saying COOL THE OIL DOWN if it's at 125c. That would be an epic concern of mine.   Im now thinking as you did Brad that the knock detection is likely due to the bearings giving a bit more noise as pressure dropped away. Kinkstah, drop your oil, and get a sample of it (as you're draining it) and send it off for analysis.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I myself AM TOTALLY UNPREPARED TO BELIEVE that the load is higher on the track than on the dyno. If it is not happening on the dyno, I cannot see it happening on the track. The difference you are seeing is because it is hot on the track, and I am pretty sure your tuner is not belting the crap out of it on teh dyno when it starts to get hot. The only way that being hot on the track can lead to real ping, that I can think of, is if you are getting more oil (from mist in the inlet tract, or going up past the oil control rings) reducing the effective octane rating of the fuel and causing ping that way. Yeah, nah. Look at this graph which I will helpfully show you zoomed back in. As an engineer, I look at the difference in viscocity at (in your case, 125°C) and say "they're all the same number". Even though those lines are not completely collapsed down onto each other, the oil grades you are talking about (40, 50 and 60) are teh top three lines (150, 220 and 320) and as far as I am concerned, there is not enough difference between them at that temperature to be meaningful. The viscosity of 60 at 125°C is teh same as 40 at 100°C. You should not operate it under high load at high temperature. That is purely because the only way they can achieve their emissions numbers is with thin-arse oil in it, so they have to tell you to put thin oil in it for the street. They know that no-one can drive the car & engine hard enough on the street to reach the operating regime that demands the actual correct oil that the engine needs on the track. And so they tell you to put that oil in for the track. Find a way to get more air into it, or, more likely, out of it. Or add a water spray for when it's hot. Or something.   As to the leak --- a small leak that cannot cause near catastrophic volume loss in a few seconds cannot cause a low pressure condition in the engine. If the leak is large enough to drop oil pressure, then you will only get one or two shots at it before the sump is drained.
    • GTSBoy
      Help! Leak coming under transmission

      By GTSBoy · Posted

      So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
×
×
  • Create New...