Jump to content
SAU Community

Car Reving From Stock Idle To 2000Rpm By Itself?

R34gymjunkie

By R34gymjunkie,
in General Maintenance

 Share

Recommended Posts

R34gymjunkie Contributor

R34gymjunkie

Posted
Posted

Installed a boost controller tonight n car was running fine on 10psi, after giving it a bit of stick in now idles from 1000rpm right up to 2000rpm at idle by itself and while driving?? Checked for vac leaks and cnt find any? Confused :(

D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted

Aac valve clean?

Block off cold start valve.

Does it idle normally if you switch it off for a second then start it again?

Mine does that. Blocking the cold start valve helped but didnt fix

come to think of it... it started on mine after i installed the boost controller.

I got the HKS evc4, what one do you have?

Maybe we should unhook the boost controllers and see.

blind_elk Grand Master

blind_elk

Posted
Posted

My car revs to 2grand and back to 1200 constantly at idle not jst sit at 2000 if that helps...

My experience is that that sort of idle indicates a fairly significant air leak. It could be in the boost controller, but you need to closely inspect every vacuum hose, especially the larger ones (like PCV to rocker hose).
R34gymjunkie Contributor

R34gymjunkie

Posted
  • Author
Posted

I think it's mechanic time, I stripped nearly all pipes n hoses today on the engine to inspect them, cleaned AAC, I'm not sure witch one is the cold start valve, I tried adjusting the tps, and aic? Still got no clue :(

D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted

Hmmm....

After reading that id say the ECU is the problem.

With all the upgrades it needs tuning.

Well thats next on my list anyway, im just trying to get as much sorted out as i can before i get the ECU and tune.

So i might let the mechanic sort this one out.

mattis96 Proficient

mattis96

Posted
Posted

wow i have exactly the same problem!!! It only happens on first start up and has to warm up to go back to normal. after i turn the car off and back on again it idles at 1000, it is very annoying, and this can be just sitting idling there, warm up for 10 mins with touching nothing, turn car off, turn car back on again with touching nothing and it is fine.

nothing gets touched or changed except it is restarted once warm and its fine, though if its not warm enough the idle creeps back up to 2500 until restarted again...

  • 1 month later...
GTR260 Proficient

GTR260

Posted
Posted

The car is designed to do what it is doing, the ecu is seeing the revs rising whilst the tps is at 0 and goes into decel to control the revs once the revs are low enough go back to normal and the revs climb again. It will keep repeating the process! My rb26 was doing this for ages and no mechanic could fix it! I end up finding the problem myself, mine was a bent butterfly on cylinder 1, ur engine is getting a significant leak from somewhere between the throttle and the head. Could be buggered throttle shaft seals or any of the gaskets between there snd the head! Even the injector seals! Either way its a air leak.

How much boost were u running when it happened? What engine and where are u? I could give u a hand to try fix it if u r local to me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • joshuaho96
      Automatic Power Button Light Flashing

      By joshuaho96 · Posted

      Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • BOLGE
      R34 Plug Identification

      By BOLGE · Posted

      Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...