Jump to content
SAU Community

Recommended Posts

"... the vehicle bearing Registration Number XXXXXX is excessively noisy and therefore likely to be exceeding the legal noise levels for the vehicle..."

"The noise test and anti-tampering inspection must be undertaken by an EPA approved Mechanic by the compliance due date which is Wednesday, 23 May 2012"

"- the engine test speed for your vehicle is 4800 rpm and the legal noise level for your vehicle is 90 dB(A)."

Again, I have a stock standard RB25DE with a K&N high flow panel filter, and a 2.5" exhaust system with a high-flow cat and 1 resonator + cannon (Will replace shitty cannon with twin tip muffler, hoping for less than 90 dB), stock extractors.

Will that pass the test? I'm just curious about the 'anti-tampering' part of it. Is a high-flow cat considered to be 'tampered' with?

Thanks.

got the exact same thing, Get a flage made up and put behind cat with steel wool stuffed in, I did and i passed at 1 DB under

Too easy.

Get a stock GTt rear muffler (assuming the pipe joints are in the original location). Plenty of flow for an RB25DE and quiet.

I was gonna say have you heard a gtst system on an na 25 but then I saw you said rear muffler. In which case probably a good way to go.

Woot, also an EPA letter in the mail for me. Zzzz. To avoid making a new topic, going to post here. Unless I get no replies... in which case I'll have to make a new thread :P.

Similar to OP; think I've got a 3" catback with huge canon (kakimoto), possible hi-flow cat (not sure). Lols (Yeah, I'm one of those). In my defense, it was on the car when I got it down from Japan, and I was initially too lazy / no monies to swap it over; and then I just got used to the sound (or maybe I just lost some hearing LOL).

What are the chances a custom made 2.25" or 2.5" mandrel bend mild steel catback, with one (or two?) centre mufflers, and a twin tip muffler of some sort; will come in under the legal limit of 90dB?

Whilst hurting my ears, I enjoyed my stupid loud exhaust sometimes in tunnels/under freeways/general spirited driving. But now that I have to change it; I figured it's high time I get the exhaust I was meant to do all that time ago when I first got it haha.

Obviously it's got to pass EPA first though, and I don't know if I can be bothered getting a stock one just for EPA, then swapping over to one I get made up. Would be better if it's possible the one I get made up is legal in the first place...

Cheers for any help brahs.

Edited by kaitoukid

i get tired of helping sometimes... nevertheless.

a 2.5 inch mild steel system with a twin tip and two center mufflers/one center and one resonator id.imagine would.come close to legal.... in saying that mines gota twin tip nd a resonator and its not even close to legal noise. hope this helps...

at the end.of.the.day if its too loud people are just offended by the noise/sound, better off having it sound nice then loud.

Haha, I'm pretty over just loud. But reluctant to make a full-time switch to stock; ideally would get one that sounds nice as well as being under the legal limit. The reason I asked straight away about that system is that's the one that's more or less recommended over and over; which I was initially going to go get ages ago anyway; but would prefer to hit two birds with one stone (change over AND clear EPA).

Just wanted to know if people thought it was possible, haha. Yeah would've thought the two mufflers would help (as well as no canon lawls) keep the sound down, but down enough is the question.... Might have to just swap over to stock for EPA and then change later; or see if there is a way to (properly) make it under the limit. Either way probably a good time to swap over from my current set up, want the next to be quieter.

Edited by kaitoukid

In regards to my car, it passed by a good 4db @ 86db. So I was all sweet, then he got it up on the hoist and started taking pictures, seeing the high-flow cat, he didn't care less about it and let me off with it :)

Costed $200 to get the EPA muffler on, will be getting something else done tomorrow that shouldn't sound too loud, I'm hoping for a nice tone. Being a N/A, are they generally louder than a T with a similar setup?

Why would they take pictures? Does it stay on file incase they get you again for the same thing?

I am pretty sure my 3" system would pass the noise test as its pretty damn quiet but its going to restrict power i think.... I was going to look at a bigger system but with size i assume comes noise :/ BUT will see how the current one performs before i go replacing anything i guess.....

yer mate natros are always going to beloude then their turbo brothers due to the design of how turbos work.

because their driven by exhaust gas and bolt directly in the flow of the gas (read noise :P) it acts as a muffler in the system.

In regards to my car, it passed by a good 4db @ 86db. So I was all sweet, then he got it up on the hoist and started taking pictures, seeing the high-flow cat, he didn't care less about it and let me off with it :)

Costed $200 to get the EPA muffler on, will be getting something else done tomorrow that shouldn't sound too loud, I'm hoping for a nice tone. Being a N/A, are they generally louder than a T with a similar setup?

I found the best muffler for sound reduction was my fujitsubo 3 1/2inch cannon with silencer inside, it was virtually silent idling, and looking round import wreckers 90% of mufflers had the silencer in them too, all Jasma complient

Now i have a 3inch Oval muffler which isnt annoying loud, sounds quite good but probably over 90db,

It really does come down to the pipe size, If a turbo skyline can make 250kw with a 2 1/2inch silencer, then a 2inch is probably heaps for the little power an NA will ever make, and alot quieter too.

2inch might actually help make more power cause im pretty sure you need a bit of backpressure with a NA motor.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...