Jump to content
SAU Community

Recommended Posts

Ok, I feel my GTS-T is feeling a little neglected so I'm considering a 100 hp shot of NOS on demand on WOT.

RB25/30 - GT3076R - Haltech Platinum 2000. 337 rwkw.

Good move ?, or should I save the dollars and wait until my kids pillage it all.

Link to comment
https://www.sau.com.au/forums/topic/398534-to-nos-or-not-to-nos/
Share on other sites

I don't drag it.

I'm hoping for a setup which the Haltech can introduce Nos only in certain gears , revs and at WOT.

But right now my injectors are maxed , my intercooler has 2 1/2 in and out, and I'm running stock manifold.

Will I still get anything more with NOS ?

I don't drag it.

I'm hoping for a setup which the Haltech can introduce Nos only in certain gears , revs and at WOT.

But right now my injectors are maxed , my intercooler has 2 1/2 in and out, and I'm running stock manifold.

Will I still get anything more with NOS ?

As long as your exhuast is up to the extra flow, yes you will see great gains. The stock intake manifold makes it easier to get a more even distrobution from single point of injection.

Your intake pipework etc wont affect the amount of extra power you can gain from nitrous.

The trick is to get the nitrous consistant. To do this you will need a bottle pressure gauge and heater on a pressure switch.

Is the engine still stock internally? If it is, I would suggest no more than 75ph fixed shot or 100hp progressive shot. If it's built, then think 100 fixed and 150 progressive, depending on boost pressure etc.

Cheers

Justin

Put a twin scroll 3788R on it instead!

I dont usually go for performance in limited quantities. Id prefer to know I can hoon interstate if I wanted to LOL

Le mans 24hr of Hoon

So get a G size bottle :woot:

Will lift the bonnet and intake manifold 10ft off the ground if it backfires though lol

Yeah... leanouts/nitrous backfires are pretty spectacular. Only ever seen them on carbied engines though... not saying it can't happen, but I've never heard of a backfire on a FI efi engine (engines that don't mix air and fuel inthe intake manifold 'plennum').

I think it's a great 'power adder'. There is no real trade off for the extra power when you'r not using it. For an extra 100hp of kick, you don't have to use a bigger turbo- more lag, you don't need bigger injectors- fuel economy/tune resolution, your not shifting the power curve up or down- if your using cams/cam gears, there's very minimal down time for install and it dosn't cost a bundle. Not to mention the dyno curve goes straight up at activation- ha ha ha!

Cheers

Justin

Thanks for all that info.

Yep car is built forged bottom end, Poncams, and Plazaman plenum.

Exhaust is stock ex manifold to 3 inch.

Intercooler has 2.5 either side.

3076 is 0.82 Ar, should have gone 1.06.

Running 21 psi now, does have more in it.

it does feel like its choking at high rpm

Edited by conan7772

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • All my Polish car culture insight comes from watching Nightride. So I half expect this to get 1UZ swapped eventually?! Are you going to drive it in winter? I'm always curious how ATTESA would hold up in the snow. There isn't that much opportunity to try it in Australia.  
    • My steering lock unit on my Infiniti G37 has failed. The car is a local 2012 Infiniti G37 (Q60 ) I need to replace the unit My local mechanic said i need to buy a complete steering wheel assembly. Does anybody no any mechanics in Gold Coast or Brisbane who can fix this issue or where i can buy just the Steering lock control unit. Thanks
    • thanks, will conduct myself accordingly. i unfortunately put about 150 miles on the car before reading this thread again, however no PS issues, and definitely no turbo issues. it spools normally and still feels fast to me, probably because my previous car was an N/A auto sedan...gonna go fix the PS vacuum line though lol. safe to say, got what i came to this thread for. thanks  
    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
×
×
  • Create New...