Jump to content
SAU Community

Change Diff From A-Lsd To Mechanical

tricstar
 Share

Recommended Posts

tricstar Mentor

tricstar

Posted
Posted

ok due to the head fxxk of the A-LSD, I've decided to change to a mechanical LSD,

so do I just need the standard diff housing? can it be an R32 GTR one ( my car is R33 GTR ), is there any difference? also will the drive shafts and tail shaft bolt staight up to the standard diff?

tricstar Mentor

tricstar

Posted
  • Author
Posted

Get one to suit a 33gtr and everything will bolt up. Go new though as usually you get everything you will need, instead of going 2nd hand and having stuff missing

but from what I have read, I need to change the whole diff housing as there is no after market diff centre to fit into the Active-LSD housing?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

I just went through it all. :)

You need to change diff housing to a R33 GTR Non V-Spec. Not expensive, can get them for 200-300 2nd hand.

I thought you needed the non-spec shafts as they are different lengths when you measure.

But it turns out the actual shafts are the same length, it's the coupling big (forget the technical name, bit where the shaft connects with) that is slightly different and I believe it can be purchase separate if you cannot get shafts to suit

Makes it easier/faster if you can get the housing with the shafts together obviously.

The car with a Nismo 1.5 GT Pro is 10000% better than with the crappy A-LSD, which has no upgrade options.

It's set to the lowest lock setting and still locks incredibly hard when you want, very predictable. Any more I think would be too much.

My car now behaves like a RWD car in terms of hooking around @ a motorkhana with a bit of clutch or trailing throttle lock-up and turn - yet straighten the wheels and it 4 wheel power slides nicely or grips and goes depending on what you want.

Also induces some good mid corner oversteer where previously it would just understeer/plough off terribly doing the same things ;)

I didn't realise how bad the A-LSD was until changing over... I don't wanna sell the car now it's changed it that much

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

I don't know mate - I was told to get a R33 rear end specifically.

I know the part numbers for R32 & R33 are the same in terms of the Nismo differential... Doesn't mean the housings are though...

Someone will be able to confirm though 100%

arrydjay Community Regular

arrydjay

Posted
Posted

I just did this in my gtst. I bought a second hand regular gtst diff and just threw it in.... everything fitted up fine for me, the only thing i needed was a new set of nuts and bolts to connect the halfshafts to the axles as the a-lsd halfshafts were threaded and the gtst ones were not....

Ripped out the pump and reservoir as well.

At the time I just shimmed the new diff, but thats shit and only lasted a few weeks and I absolutely locked the fark out of it.... next mod is either a kaaz or nismo centre.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Ye that doesn't surprise me.

Ideally yes you want diff & axles. It just makes it a simple bolt in/out (once you do the centre.)

But... if you can't get the shafts, you can use your v-spec ones as they are the same length. It's just the the coupling bit that's the different length betweeen VS and non-VS (the technical name for the part still escapes me)...

I can find out the proper name and shit next week exactly and report back. I doubt you'll find a R33 non-VS rear in a couple days. I was looking for a good 2 months for one priced appropriately.

bigmikespec Veteran

bigmikespec

Posted
Posted

spoke to a mate in the know last night and the R32 GTR diff and axles is a touch shorter...

so I'm after a R33 GTR non-Vspec diff and axles, anyone ??

Yes they are, I have measured them as I have a R32 GTR diff. from a 1994 car to replace my A-LSD. Just need some spacers machined, from memory it is only about 5mm.

tricstar Mentor

tricstar

Posted
  • Author
Posted

OK I've got the Non V-spec diff and axles,

now I have a few questions about what to do regarding the hydraulics and electrics?

My thinking is, just block off the hydraulics from the pump under the car and rip everything from there to the diff out.. I'm thinking I shouldn't need to cut or disconnect any wiring (except the obvious between pump and diff) as the new diff will be locked before any signal is sent.? Being that the A-LSD is on the same circuit as the AWD I don't want to hack it and then get faults with the AWD ?

How do others do it ? What have you blocked off, cut etc?? (Nismoid)?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

The Transfer case & rear diff pumps are all in the same cradle so easier just to leave them there and remove the lines which is what happened to mine.

I cant remember if the power feed for the A-LSD was disconnected. It's not throwing any failure lights, i know that much. I'll find out and report back next week.

tricstar Mentor

tricstar

Posted
  • Author
Posted

The Transfer case & rear diff pumps are all in the same cradle so easier just to leave them there and remove the lines which is what happened to mine.

I cant remember if the power feed for the A-LSD was disconnected. It's not throwing any failure lights, i know that much. I'll find out and report back next week.

cool, can you also have a look and see if they blocked off the line from reservoir in the boot or just the line from solenoid to diff?I should do a DIY when I do the swap for future reference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Intro/R33 owner

      By PranK · Posted

      Welcome!  How long have you had it? And what colour is it?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      "CAD" version 1.0 It will have a 15mm lip around the top for 6 × 5 or 6mm nutserts and fixtures (two on each of the three straight edges), and some pinch weld on any exposed edges, it has three mounting points, one of the power steering reservoir bolts, and two on the rad support, my 120mm hole saw will make short work of hole for the silicone joiner, with ample room for some pinch weld  I've also got enough Carbuilders "peel and stick" heat shield to cover the outside of it at the coolant expansion tank and on the engine side, as pictured, and internally on the lid and where the fuse box is, I've also got some thin, about 3mm, black 3M single sided sticky foam stuff that was left over after sealing some door drafts at home to help seal the lid As for the shape, it "sort of" matches the shape of the fuse box, so shouldn't look to "out of place" The lower area and hole for the intake will need pinch weld with a balloon on it to fully seal the hole and bottom of it, that will happen after it has been fabricated so I know exactly what size is required  Filter service has been trialed,  and so far it was a simple process  Just need to get some alloy, and then head into work to use the guillotine and break press in the workshop Hopefully it should be sorted in a week or two Guestimated outlay will be under a $50 for the stuff I don't have on hand (alloy, 6mm nutserts, the pinch weld, and wrinkle paint) Disclaimer: That's what the "voices in my head" are telling me how the filter box should end up getting done......lets see if they know what they are talking about  
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Have been polishing up the trailer rims as they had been sitting in the shed for a few years and are really in need of some love. This was after a couple of passes with chrome polish - coming up quite well ✅ .
    • MBS206
      Intro/R33 owner

      By MBS206 · Posted

      Welcome aboard! Is your Skyline auto or manual? I'm assuming manual. Does it have any mods done yet?
    • Yeetus
      Another "where do these lines and plugs go" RB25DET question

      By Yeetus · Posted

      Hey mate, the brown and grey plugs would usually go to the TPS, brown one goes on the bottom connector and grey is the top but isn't used unless the car is auto, your TPS looks different to mine though I've got a series 2 engine.
×
×
  • Create New...