Jump to content
SAU Community

Change Diff From A-Lsd To Mechanical

tricstar
 Share

Recommended Posts

tricstar Mentor

tricstar

Posted
Posted

ok due to the head fxxk of the A-LSD, I've decided to change to a mechanical LSD,

so do I just need the standard diff housing? can it be an R32 GTR one ( my car is R33 GTR ), is there any difference? also will the drive shafts and tail shaft bolt staight up to the standard diff?

tricstar Mentor

tricstar

Posted
  • Author
Posted

Get one to suit a 33gtr and everything will bolt up. Go new though as usually you get everything you will need, instead of going 2nd hand and having stuff missing

but from what I have read, I need to change the whole diff housing as there is no after market diff centre to fit into the Active-LSD housing?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

I just went through it all. :)

You need to change diff housing to a R33 GTR Non V-Spec. Not expensive, can get them for 200-300 2nd hand.

I thought you needed the non-spec shafts as they are different lengths when you measure.

But it turns out the actual shafts are the same length, it's the coupling big (forget the technical name, bit where the shaft connects with) that is slightly different and I believe it can be purchase separate if you cannot get shafts to suit

Makes it easier/faster if you can get the housing with the shafts together obviously.

The car with a Nismo 1.5 GT Pro is 10000% better than with the crappy A-LSD, which has no upgrade options.

It's set to the lowest lock setting and still locks incredibly hard when you want, very predictable. Any more I think would be too much.

My car now behaves like a RWD car in terms of hooking around @ a motorkhana with a bit of clutch or trailing throttle lock-up and turn - yet straighten the wheels and it 4 wheel power slides nicely or grips and goes depending on what you want.

Also induces some good mid corner oversteer where previously it would just understeer/plough off terribly doing the same things ;)

I didn't realise how bad the A-LSD was until changing over... I don't wanna sell the car now it's changed it that much

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

I don't know mate - I was told to get a R33 rear end specifically.

I know the part numbers for R32 & R33 are the same in terms of the Nismo differential... Doesn't mean the housings are though...

Someone will be able to confirm though 100%

arrydjay Community Regular

arrydjay

Posted
Posted

I just did this in my gtst. I bought a second hand regular gtst diff and just threw it in.... everything fitted up fine for me, the only thing i needed was a new set of nuts and bolts to connect the halfshafts to the axles as the a-lsd halfshafts were threaded and the gtst ones were not....

Ripped out the pump and reservoir as well.

At the time I just shimmed the new diff, but thats shit and only lasted a few weeks and I absolutely locked the fark out of it.... next mod is either a kaaz or nismo centre.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Ye that doesn't surprise me.

Ideally yes you want diff & axles. It just makes it a simple bolt in/out (once you do the centre.)

But... if you can't get the shafts, you can use your v-spec ones as they are the same length. It's just the the coupling bit that's the different length betweeen VS and non-VS (the technical name for the part still escapes me)...

I can find out the proper name and shit next week exactly and report back. I doubt you'll find a R33 non-VS rear in a couple days. I was looking for a good 2 months for one priced appropriately.

bigmikespec Veteran

bigmikespec

Posted
Posted

spoke to a mate in the know last night and the R32 GTR diff and axles is a touch shorter...

so I'm after a R33 GTR non-Vspec diff and axles, anyone ??

Yes they are, I have measured them as I have a R32 GTR diff. from a 1994 car to replace my A-LSD. Just need some spacers machined, from memory it is only about 5mm.

tricstar Mentor

tricstar

Posted
  • Author
Posted

OK I've got the Non V-spec diff and axles,

now I have a few questions about what to do regarding the hydraulics and electrics?

My thinking is, just block off the hydraulics from the pump under the car and rip everything from there to the diff out.. I'm thinking I shouldn't need to cut or disconnect any wiring (except the obvious between pump and diff) as the new diff will be locked before any signal is sent.? Being that the A-LSD is on the same circuit as the AWD I don't want to hack it and then get faults with the AWD ?

How do others do it ? What have you blocked off, cut etc?? (Nismoid)?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

The Transfer case & rear diff pumps are all in the same cradle so easier just to leave them there and remove the lines which is what happened to mine.

I cant remember if the power feed for the A-LSD was disconnected. It's not throwing any failure lights, i know that much. I'll find out and report back next week.

tricstar Mentor

tricstar

Posted
  • Author
Posted

The Transfer case & rear diff pumps are all in the same cradle so easier just to leave them there and remove the lines which is what happened to mine.

I cant remember if the power feed for the A-LSD was disconnected. It's not throwing any failure lights, i know that much. I'll find out and report back next week.

cool, can you also have a look and see if they blocked off the line from reservoir in the boot or just the line from solenoid to diff?I should do a DIY when I do the swap for future reference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Lithium
      Garrett G Series

      By Lithium · Posted

      What do you mean?  In between the two I shared?  They're the same boost   This will be insane.   A mate has a GTSt with a 9:1 RB30/25 with Tomei 256 cams and a Borg S362SX-E that is already a beast from the basement but has a stock 5 speed and will probably get a ZF8 one day.  After the G35 900 RB26 setup I'd be lying if the topic of "Wtf would a divided G35 be like on this thing?" idea hadn't come up - you'd definitely want a wide boost control range setup with it, as even with the less responsive and potent S361 we're having to ramp boost in from very low levels in the early gears.
    • joshuaho96
      Upgrade an rb25neo

      By joshuaho96 · Posted

      ZF8 is faster, wider ratio spread, better in every way. I do not dispute this. But I have brain damage and I want the feeling of shifting gears. To me the extra work is fun, but I daily an automatic and in the US like 90+% of cars are automatic so a manual transmission is an "exotic" experience. If I want an automatic I've driven an F80 M3 with DCT more than a few times and it's incredibly capable but it's emotionally vacant to me.
    • Lithium
      Upgrade an rb25neo

      By Lithium · Posted

      Different folks for different folks I guess - for me, the 6MT > ZF8 claim is wild.  If I had a manual Skyline I'd be saving up fix that with a ZF8.  I went for a M135i, has the N55 which resolves a lot of the issues the N54 has, it already has the ZF8, is barely heavier than an R34 GTt, full boost before 2000rpm while also being real-word-faster than my old 280kw @ hubs R33 GTS25t and doing absolutely everything better.  There's nothing I'd change on it to be more like my old Skyline, tbh... it doesn't sound the same but it's got it's own awesome sound - definitely not worse.   To be fair I can't argue with most of those points.  I guess i was pointing it out as a comparison for a Skyline GTR and it's much closer all around there, like the weight difference between an M240i and an R34 GT-R isn't that much etc.   As above, I ended up getting an M135i which is in the 1400kg range - the M140 and M240is that you can get up till 2018 are B58, ZF8, RWD and in the 1400kg range which is a bit of fun... but doesn't fit the tyre etc of the Supra.  They are a run drive, though- maybe no an A90 Supra but a huge upgrade over a Skyline "sporty chassis" wise.    
    • waxracing
      Garrett G Series

      By waxracing · Posted

      Im loving this thread. I have a g35/900 t4 split 1.00 ar going on my rb30/25 with 9:1 and 264 cams. its drive by wire and with vct i think it should spool nicely. I have the 8speed gearbox on the floor ready to go on so full boost changes will be a thing if the tyres can deal with it. it should always be on boost
    • joshuaho96
      Upgrade an rb25neo

      By joshuaho96 · Posted

      The trouble for me is the automatic takes away so much from it. And the E92 has hydraulic power steering. Even after putting in an LSD you're looking at re-mapping the xDrive to be more like a Skyline which is just a lot of effort for something that is supposed to be easier and cheaper. I consider the E92 335i 6MT to basically be the obviously superior car to something like an R34 GTT. Half the price out here, the N54 makes so much more power so easily, is a far more refined car, etc. You do have to deal with the nightmare of the N54's foibles vs the B58 which is comparatively miles better and if a turbo does fail it's only one of them vs two and a lot less pipe spaghetti.  996 or 997 Turbo has the AWD system mapped like a Skyline. Basically always RWD unless engaging the front axle makes sense. A coworker let me drive his 997.2 Turbo 6MT and it's absolutely tremendous. I don't think I'd want more power in a street car.
×
×
  • Create New...