Jump to content
SAU Community

Gtx3076R Pick My Tune Apart Please

Selleck 34GTT
 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

At the end of the day it just flows X amount of air through the compressor, how much of it the engine can't ingest gives you the boost figure. I couldn't run more than 23psi on the final tune with the GTX3071 with 1.06 rear, the compressor was way out of efficiency and it made less power from heating the air with no benefit.

I just slotted the GTX3076 with .82 rear in today so I will let you know the outcome Wednesday hopefully. I can already tell its much more responsive... :)

AngryRB Grand Master

AngryRB

Posted
Posted

giddy up, will be watching for your results, one day mine will get tuned too to add to the GTX results. Just need a resonator and wait for a dyno to be available, they all booked out in brissy for winterinternationals and jamboree i think.

AngryRB Grand Master

AngryRB

Posted
Posted (edited)

he first tuned it without E85 and made 288kw with a 0.82rear on about the same boost,

4300rpm to get 200kw so they are comparable , take 20kw off for the rear housing difference and its very close, take into account a slipping clutch was was noted, and they would be very close at that point.

so looks like the two are not far apart, and personally the sound of the 76 even in GTX form is awesome. :whistling:

Edited by SliverS2
scotty nm35 Grand Master

scotty nm35

Posted
Posted

I should be able to get an overlay of both graphs but I can feel the .82 is perfect, probably for either turbo, and as they have the same turbine, they should feel much the same on the road.

Mine with the stock airbox is still silent. :(

Mitcho_7 Mentor

Mitcho_7

Posted
Posted

So you both will be running .82 ext. gates in the gtx3076? Interested to see the results.

Was mickos 98 tune with a low mount .82 internal gate? 200rwkw by 4300 is pretty responsive in my view. I know he was pumping a fair bit of boost, but that might have just been on e85.

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

a .63 housing on a gtx3076 is a little silly. you'd be much better off with a gtx3071 or a normal gt3076 as with the .63 you'll be limited to a fair bit less than the x76 compressor can flow.

still, not a bad graph considering. the advantage is when you want a little more you can simply bolt on a bigger housing and maybe a better manifold and make a fair bit more

simpletool Mentor

simpletool

Posted
Posted (edited)

You could try to up the gain on the boost controller and possibly end up with a slight boost spike. Looks like the boost is set to 18psi but doesn't quite control it near max torque (~45-5000rpm). I suspect the thing is VERY close to compressor surge while boosting and your getting some very slight symptoms from that. With a compressor bigger than a 76mm 56 trim and with a 0.63A/R it'd have to be close to surge.

You can't tell driveability or response from a dyno sheet. How does it FEEL coming onto boost? Does it actually make fast boost at 4000rpm? What are the mixtures like?

Edited by simpletool

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • oHBoy.
      Starter motor replacment teeth count.

      By oHBoy. · Posted

      I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...