Jump to content
SAU Community

Hks Oil Cooler Flushing And Health Check

Tmac9091

By Tmac9091,
in General Maintenance

 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Flush the cooler with kero or similar I guess. Make sure there are no metal particles in the oil that comes out, it could mean the engine blew before it was removed.

You can test the thermostat in boiling water, most open around 80 degrees.

Victory Mentor

Victory

Posted
Posted

I am in a similar position as I have recently acquired a genuine R33 GTR N1 oil cooler in mint condition.

I would like to use it in my GTR so I am going to flush it with the same mixture that you clean intercoolers with - Equal parts of kero and mentholated spirits. You would be amazed how much oil this mixture gets out of what looks like a clean intercooler.

If anyone has any better ideas I am open to suggestions.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Murray_Calavera
      WTAC 2025

      By Murray_Calavera · Posted

      Yeah mate, never miss it.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Any going to watch World Time Attack at SMSP this year?
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
    • zillah
      Recommendation for engine oil funnel spill free

      By zillah · Posted

      hahaha good on
×
×
  • Create New...