Jump to content
SAU Community

Recommended Posts

You pair have nothing

You want a long cruise head out through cessnock to broke then take Charlie's road across to putty rd the head out the golden hwy to sandy hollow and turn onto Bylong Valkey way which goes back to Richmond then a short hop to Windsor and back up putty road to singleton and home

that doesnt look too bad, but looks to actually be a shorter route!

The Putty run we did a few years back was a long day, we did Old Pac, Galston Gorge, Windsor and then Putty Rd through to Singleton..... It was a 2 fuel stop trip on that run..... On that note, how far is that drive in KM? And have you mapped out fuel stops? (Taking into account that ill only make <300kms to a tank lol

ful trip is 650kms... you would have to see where to get your fuel from.

I will bring a spare bottom end, ill have to change that out when u guys fix what u break :ph34r:

Good plan! Anyone got a 2 poster they can bring?

that doesnt look too bad, but looks to actually be a shorter route!

ful trip is 650kms... you would have to see where to get your fuel from.

I fuelled up in Sydney and then again in Singleton on our run.....

But my flex fuel is back on now so i can run whatever, not an issue :) Just have to run low boost with normal pump fuel :( Only 19psi lol

may need to plan this one for winter so its easier on the cars haha..

Yeah plus cooler = more wasps! And if the car bursts into flames we can all sit around the campfire and inhale the E85 goodness!

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

Is the head still good?

If its a DE as you say then any VL bottom end with a light hone, new rings and bearings and your head fitted should do nicely

You need to fit an idler pulley for the belt return and I think that's it

Best bet is to do a search on here as there is a heap of info around just have to find it

As far as legalities go I'm not sure but if original engine number then no capacity increase

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

Sell car and get a PULSAR VZ-R N1. Iron chef has one up for sale. SR16VE N1 Engine.... stock 200hp, 1090kg and 6.8 secs 0-100

Put on a full exhaust, apexi power FC, splitfire super direct ignition,etc and youll have around 300hp at the flywheel and 0-100 in 5 second territory.

Sell car and get a PULSAR VZ-R N1. Iron chef has one up for sale. SR16VE N1 Engine.... stock 200hp, 1090kg and 6.8 secs 0-100

Put on a full exhaust, apexi power FC, splitfire super direct ignition,etc and youll have around 300hp at the flywheel and 0-100 in 5 second territory.

Face palm :no:

f**k that sucks man. wonder how much it'll cost to how much you could sell it for.

N/A engines should be cheap and pretty easy to get ahold of man!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...