Jump to content
SAU Community

Recommended Posts

When you are travelling at 100km/h, it is possible your speedo could read as much as 110km/h and still be classified as 'normal'. But most will generally only read about 5% fast. show 105km/h when travelling at 100km/h.

Link to comment
https://www.sau.com.au/forums/topic/403051-speedo/#findComment-6410823
Share on other sites

it means your tyre size is contributing to your speedo inaccuracy. not causing the full 10% error, but at least some.

You should be running a 50 profile for that size tyre/rim (235/50/17), to match the standard tyre diameter.

Link to comment
https://www.sau.com.au/forums/topic/403051-speedo/#findComment-6418294
Share on other sites

It will still be out. My speedo displays 100k's when I am doing 90, but the Informeter I have displays the correct speed so the ecu isnt the issue, the speed error is inside the dash unit from the factory. You would have to go for a much larger tyre size to correct it.

Link to comment
https://www.sau.com.au/forums/topic/403051-speedo/#findComment-6418662
Share on other sites

^^ as scotty said.. the tyres you have aren't 10% smaller than the correct size, so you aren't going to recover the 10km/h. For example, you might only be about 7km/h out instead of 10km/h at 100.

Mine reads about 2% fast, so when the speedo reads 100km/h, I am actually travelling at about 98km/h, but my wife's J31 maxima is worse.. it is about 6%. in each case the ECU reads correct, it is just the speedo unit that shows the wrong speed.

Link to comment
https://www.sau.com.au/forums/topic/403051-speedo/#findComment-6418715
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...