Jump to content
SAU Community

Recommended Posts

This is for my parents Honda car. I want to replace their steering wheel, but need to disconnect the battery so I don't trigger the airbags. Problem is once I disconnect the battery, the alarm goes off. It's a mongoose, though not positive as to what model. I have that little key, which I used on the alarm speaker thingy and it seemed to shut it off ok. But upon closer inspection it's still actually chirping away, be it at like 2% noise instead of it's regular 100%.

The siren speaker looks like this

MSP80.jpg

If I was to take this thing apart, is the battery backup battery inside this thing?

The alarm works ok. If I have to I'll let it chirp for 10mins or so while I take the steering wheel off, then unplug the airbag connectors. Connecting the main battery terminals stops the chirping and everything again works as it should. So it's only during the period I have the battery disconnected so I don't trigger the airbags, that I want to shut the alarm off. Using the key on the siren shuts it off, but only 98%. Put your ear close to it, you can still hear it. If that's all I have to deal with for 10mins or less I'll live with it. I don't think getting a new alarm is going make any difference and seems excessive for simply wanting to replace the steering wheel.

Chris is right.. new siren.

As far as I know it's a sealed siren.

In frustration I cut the wires, pulled it out and couldn't crack it open.

I smashed mine open because it just would not stop. Suppose I could have drowned it !

There is like 8-10 disc batteries rolled in clear plastic.

Sounds like it got wet , the keyholes leak , even 1 drop and it shorts the key curcuit

Drowning it wont stop it , i tested my old one in a bucket of water , it sounds wonky but still going off and got louder as it dried again ( it was farked but still going )

New siren time , 99 bucks

Drowning it wont stop it , i tested my old one in a bucket of water , it sounds wonky but still going off and got louder as it dried again ( it was farked but still going )

Old siren still has 3 uses...

1) insert into coffin for burial > frightens graveyard vandals away

2) additional location device for searchers of black boxes from ditched aircraft

3) place under mother-in-law's bed to remind her that she's forgotten to take her hearing aids out before retiring

;)

I had the same alarm. turning the key on the actual siren only makes it a bit quiet like you said. but i dont see why you cant leave the siren chirping at a very very low volume which you can barely hear, for a while. i left mine like that for about two days and then put it back on.

I got it all sorted. Turned the key, unplugged the battery and it did it's near silent chirping business. I got on with unplugging things, replaced the steering wheel and then reconnected everything. Once I connected the battery back again, the chirping stopped. Then turned the key to put it into normal mode and it's all working good again. This took 5-10mins.

I can live with the minor fault of it not been entirely silent when the key's turned and the battery is unplugged. That's not an everyday situation either so not like I'm going to have to deal with this on a daily occurrence.. As it stands right now, the alarm arms, chirps, and goes off just fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...