Jump to content
SAU Community

Recommended Posts

Hello all, unfortunately i think i'm going to have to sell my RB26 and all the associated parts i have bought for it so far. I've gone a bit overboard with my RB25 which leaves me struggling to finish the rest of my car. All the other parts are up for sale.

I'm in Adelaide.

Photos for the RB26 and parts can be organised if you need them.

This is just an EOI for the RB26 and parts to suit.

What i've got;

RB26 complete minus coil packs and injectors. Hot side completely removed but included. Cast mounting point for the alternator was broken off the block when the vehicle was in an accident, could possibly be welded back on. Wiring loom has been stripped of all un-necessary wiring (1/2 complete), ECU, 1x good AFM, 1x damaged, Harmonic Balancer damaged. engine is otherwise complete. Looking at $1800

R33 RB26 Block and crank very good condition - Was to replace the damaged block - $600

CP 86.5mm RB26 pistons new in the box - $800 Firm - Cheapest you can get them for is $900

RB25/RB26 Carrillo Pro H Beam Connecting Rods with CARR Bolts - One of the best rods on the market! - $1400 (These cost me $1600 a year ago). These rods are for the serious builder.

Full Genuine Nissan RB26 Gasket Set - $250

Brand New Tomei Inlet Adjustable Timing Gear - $200

ARP RB26 head studs new in box - $300

WIll do a deal for multiple items bought at once or the whole lot.

Brand new in the box Greddy Profec B Spec II - Going with closed loop boost control with my new ECU so this is not required - $320 including express delivery to you.

R34 RB25 NEO ECU (Auto) and Nistune. The Nistune board is NOT installed into the ECU yet. - $400

RB25NEO Harmonic Balancer. Brand New Genuine Nissan item. I bought this from KMS several weeks ago, but i have now gotten ROSS to make me up a custom NEO harmonic balancer. This is no longer required. Brand new, suits all cars with the NEO engine. $320

P6110305.jpg

RB25DET NEO pistons and rods - 39,000km on them. Very good condition. I'm forging my engine so these are not required. $200

P6110304.jpg

RB25DET Neo engine cover - very good condition, no broken plastic, comes with all the mounting brackets - $100

P1020123.jpg

P1020124.jpg

NEO intake pipe, recirculation pipe and cross over pipe - $100 ono

P1020136.jpg

PM sent

SMS Sent

Would you sell block with girdle only (minus crank)?

Sorry mate, crank stays with the block and girdle. Tried to PM you but your inbox must be full.

I have personally looked over it and found no issues at all. Im quite anal about engine parts and the block and crank are in great condition. If it wasnt i wouldnt have bought it.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...