Jump to content
SAU Community

Recommended Posts

The lights in question on IM are RHD, which are legal in Australia.

Why buy LHD? You don't want to waste money, yet for the lower upfront cost you want to take the risk that you wont get defected for headlights.

If you do go down this route and get LHD lights, and you do get defected for it, it will cost you more in the long run.

If you are going to do something, do it right the first time.

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

The lights in question on IM are RHD, which are legal in Australia.

Why buy LHD? You don't want to waste money, yet for the lower upfront cost you want to take the risk that you wont get defected for headlights.

If you do go down this route and get LHD lights, and you do get defected for it, it will cost you more in the long run.

If you are going to do something, do it right the first time.

I'm just worried about the bad output, i like to be able to see where i'm going at night. These G35 projectors look good and are very good quality, i don't know what i prefer i'd rather stock lights than aftermarket and i'm not in love with the look of the lights on IM so yeah. Still deciding.

As am i, i'll only purchase them if i can't find any good quality RHD lights. Might actually end up buying the aftermarket CCFL xenon's and replace the bulbs for 8000k or something.

Don't get 8000K HID's (if thats what you meant)

it will by far be the worst decision you ever make in lighting. I drove next to a subaru WRX with what looked like 10,000K bulbs not to long ago (looked purple) and I could see the vision they were providing him, and it wasnt great at all.

I have 4300K in both low and high beam. The high beam kit I bought is much better then the cheaper low beam kit I got, but both provide a crisp light output. Its hard to explain the higher Kelvin lights, they light up the road, but they light it up dull-ly?

from what I've heard 5500K is about the highest you want to go. This is the stage just before your light output starts getting blue as well, just a nice white light.

My high beam kit was $180 with a relay harness I'm pretty sure, and is the kit I would buy again. They heat up about 3 times faster then my cheap low beam kit

The term 'xenon' can be misleading. You can get xenon halogens, and HIDs also use xenon gas. So you are better off defining them as halogens or HID.

I don't think you will be unhappy with LHD headlights. It will just be other drivers who will be unhappy. And you run the risk of a defect.

The human eye is less sensitive to the shorter wavelength light, that is why the higher colour temp. Lights can appear dull.

Edited by sonicii

what I want to know is what do they do with the stock HID's at compliance... chuck em' in the bin or sell on ebay? There has gotta be another market there that we could possibly buy back what is rightfully ours right?

what I want to know is what do they do with the stock HID's at compliance... chuck em' in the bin or sell on ebay? There has gotta be another market there that we could possibly buy back what is rightfully ours right?

Now that is a can of worms, as the HID kit is not "legal" it is removed from the car, therefore you have no right to the parts.

I have an aftermarket set of projectors on my sedan with an aftermarket HID kit (6000K) and the road is lit up very well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...