Jump to content
SAU Community

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Running in dyno pull at 20psi of boost pressure. Responding nicely

your dyno guy above is a splitting image of my brother - i shared this clip with my mates & we all had a laugh about it!

Enough said.

538773_10151173938879571_454310209_n.jpg

congratulations - 1430nm is absolutely massive!

my rb26/30 made 930nm on a dyno dynamics dyno - would it be accurate to say that your engine makes in the vicinity of 50% more torque? if so, i don't think i could even begin to imagine how this feels...

not bad Martin, i was expecting the turbos to come on later in the rpm

do you feel that power loss below 3800 on the road? does it feel light switch through the midrange?

Edited by domino_z

Domino, it shows to boost slower than it actually does as we needed to use a faster ramp rate on the dyno to keep full traction at all four.

In other words its not that much laggier than stock, with a massive seam of torque once its 'on'

Quite impressed with this combo actually :)

  • 2 weeks later...
  • 2 weeks later...

Saw this car on display on the weekend, looking good, cant wait too see it unleash down the strip! Let me know when its going to be down there Errol....

Cheers Cale

  • 2 months later...

martin, as you know we have been moving and no time to drive this vehicle. have now had the extreme pleasure of driveing about 300 kilometers and the more i drive it the more impressed i am by the whole package that you have put together for us. the torque is awsome to say the least and it comes on incredibely fast and furious. i will run it in properly over the next couple of months before heading to the local drag strip. the amazing thing is that even with this package the vehicle is quite driveable. thanks for all your help in putting this all together.

martin, as you know we have been moving and no time to drive this vehicle. have now had the extreme pleasure of driveing about 300 kilometers and the more i drive it the more impressed i am by the whole package that you have put together for us. the torque is awsome to say the least and it comes on incredibely fast and furious. i will run it in properly over the next couple of months before heading to the local drag strip. the amazing thing is that even with this package the vehicle is quite driveable. thanks for all your help in putting this all together.

Make sure you let us know when it is going to the strip please errol

  • 2 months later...

Sure will Errol. Domino, in short Rooters car is a built Trust 3.8 engine with ported heads equipped with a TD06 turbocharger kit, Syvecs management, and all the fruit to make it run good power on E85 (2000cc injectors etc.) If you want a detailed, detailed list then let me know. Its a nice tight combo, and the TD06 kit is one of our favourites, as not only does it work well, but its engineered for RHD GTRs unlike most anything from the USA (big consideration that one if you dont want to spend extra money fixing steering rack clearance issues) :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...