Jump to content
SAU Community

Recommended Posts

Hey guys,

I own a R34 GTR, recently my power steering belt snapped so i took it back to my dealer because it was still under warranty. They told me that the aftermarket pulley that was on my car was made for a R32, thus the reason why the belt came off. Okay true, i understand that bit.

After a few days, i headed down to the dealers mechanic to pick up the car, from what i can see the pulley was replaced but strangely enough i noticed that the balancer was also replaced. I was running an after market one from what i could see when i first picked up the car. (They told me they didn't change it, and only replaced the pulley and the alternator pulley but the aftermarket alternator pulley is still there)

Anyways, driving the car back it felt very different, it was no as responsive as it was before, it just didn't have that little edge it once had. (Noting that the car was tuned, Power FC, cams, and full exhaust)

I was just wondering by changing the pulleys back to standard would it make that much of a difference that i can feel a change in power delivery? Or was my assumption of them changing the balancer as well contributed to the change of responsiveness i now have in my car?

I am pretty upset about this as I have no proof to say they did and I did trust them enough to leave my car to them.

Any help will be greatly appreciated.

Lightweight crank pulley = less rotating mass for the crankshaft to turn. Might free up a few kw depending on how much of a weight difference there is between stock & aftermarket. I have one on my car and it makes a small but noticeable difference.

Thanks for that, when i mentioned pulley they replaced the aftermarket crank and the power steering pulleys. Was that necessary if it was only the power steering pulley that was not aligned properly?

the name was rocket something... or vise versa. the reason i knew is i had a look at it before i took the car there, and when i had a look at it again at the workshop it was sitting in the passenger side floor and i had the stock one put back in.

That's what i thought, only the power steering required changing. Damn got robbed.

The thing that got me was when i asked for the parts back i was told they never replaced it when it was obviously clear it was. All the belts were changed back to stock as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...