Jump to content
SAU Community

Neo Fuel Problem

JonnoHR31

By JonnoHR31,
in Engines & Forced Induction

 Share

Recommended Posts

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

Just finished putting an auto er34 rb25det into a manual hr31, wired it up and got it running yesterday. It started straight away and idles like a dream, except the ecu isn't putting in any extra fuel when pumping the throttle, making it UN-drivable.

I've been over the TPS wiring several times, its got power and at the ECU plug the signal wire reads .45v when closed and 4.0-4.1v at WOT so the ECU is getting the TPS signal and it's working as it should. As far as i know the TPS signal is the only thing the ECU uses for throttle pump injection so this has me stumped. Does anyone have any ideas why this wouldn't be working and how to fix it? Possibly something I've missed in the wiring? Or is there something else than can cause the same symptoms (stabbing the throttle causes revs to drop until the ECU picks up the extra flow via the AFM) that I'm missing?

Link to comment
https://www.sau.com.au/forums/topic/406040-neo-fuel-problem/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

You need to get a consult connection going so you can see what's going on.

You're also going to need to Nistune it if you want to be able to get around the lack of traction control and ABS that the ECU expects to see. Otherwise it will throw codes about the TCS/ABS comms and the TCS throttle position sensor.

JonnoHR31 Grand Master

JonnoHR31

Posted
  • Author
Posted

Consult isn't really possible at the moment unless I can find someone local with one, might have a scope around the WA section.

There was always going to be error codes but I was under the impression they wouldn't affect the actual running of the motor? I've taken it for a test drive and apart from this throttle hesitation it drives perfectly and doesn't have any cuts under full boost or anything.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Is it all still connected? If the ECU can't see the TCS TPS it'll have a fit.

The ECU still chucks a wobbly even if it is connected - if there is no TCS computer present to make the throttle do the close-open dance when the ignition is switched on. That's one of the error codes that comes up. Nistune can mask it.

And this stuff can still cause hassles even if you get past all these little annoyances. The Nistune blokes worked out that if you do not have the TCS stuff working, when you up the boost/flow and get up to a reasonably high power level, then the ECU starts pulling shenanigans that feels like a rev/boost limit, and can't be tuned out. It is possible that Stagea ECU images do not have that problem (as they do not use TCS).

GTSBoy Grand Master

GTSBoy

Posted
Posted

Got it sorted, had the ECU boost sensor hooked up to the manifold, moved it to the intake and now it's running fine. Weird.....

That'll do it. I just checked my engine. That sensor is connected to the crossover pipe immediately adjacent to the BOV. I guess it is not supposed to see vacuum.

Hanaldo Grand Master

Hanaldo

Posted
Posted

The ECU still chucks a wobbly even if it is connected - if there is no TCS computer present to make the throttle do the close-open dance when the ignition is switched on. That's one of the error codes that comes up. Nistune can mask it.

And this stuff can still cause hassles even if you get past all these little annoyances. The Nistune blokes worked out that if you do not have the TCS stuff working, when you up the boost/flow and get up to a reasonably high power level, then the ECU starts pulling shenanigans that feels like a rev/boost limit, and can't be tuned out. It is possible that Stagea ECU images do not have that problem (as they do not use TCS).

Spot on. It's very annoying :glare:

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

One of the wires was broken but it didn't make any difference.

Got it sorted, had the ECU boost sensor hooked up to the manifold, moved it to the intake and now it's running fine. Weird.....

Can u Please explain this a little more?

Had a 34 come in that had the same symptoms as urs after another mechanic did a headgasket. I had to disconnect the boost sensor to stop it trying to stall on takeoff. Such a simple little thing

JonnoHR31 Grand Master

JonnoHR31

Posted
  • Author
Posted

It seams to not like seeing vacuum, so just make sure it's hooked up somewhere before the T/B and it should be fine.

Thanks for the suggestions everyone.

Hi Jonno, i know its off topic but why did you get rid of your RB30DET and put a AUTO RB25DET neo into your HR31?

Sold the car to my younger brother, put a stocker neo (it's now manual) in for him and I'm selling my engine seperately along with a lot of other stuff.

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

It seams to not like seeing vacuum, so just make sure it's hooked up somewhere before the T/B and it should be fine.

Thanks for the suggestions everyone.

Sold the car to my younger brother, put a stocker neo (it's now manual) in for him and I'm selling my engine seperately along with a lot of other stuff.

ah cool . . . are you using the auto ECU that you got with the motor? could be causing issues if you are?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...