Jump to content
SAU Community

Recommended Posts

I have a S1 Stagea RS4 auto with the under dash hand brake + release handle, I've just had the rear brake pads replaced and last night I noticed the (!) symbol flickering on & off whilst driving.

Is there a sensor for this light? Or do I just need to find the hand brake cable and apply some grease?

Any thoughts?

Link to comment
https://www.sau.com.au/forums/topic/406053-sticking-hand-brake-light/
Share on other sites

actually, it is more likely to be low brake fluid - the handbrake light is also used for that.

Have a look at the fluid level in the large resoviour in the engine bay near the driver's a pillar. If it is low you either have a fluid leak (bad) or your pads and discs are low and ready for replacement

Aren't there two resivours and if so where are they, i know the one near the break booster but someone was talking about one below there or something. I think i have this same problem or at least i hope it's this simple!!!???

sorry I wasn't very clear - the warning light is either handbrake on or low brake fluid, and low brake fluid only happens from a leak or sometimes pads worn.

If you have plenty of fluid in the master cylinder, it must be the handbrake switch not releasing properly.

sorry I wasn't very clear - the warning light is either handbrake on or low brake fluid, and low brake fluid only happens from a leak or sometimes pads worn.

If you have plenty of fluid in the master cylinder, it must be the handbrake switch not releasing properly.

Thanks Duncan, I'll have a look to see what I can do!?

  • 1 month later...

Has anybody located the switch I'm referring too?

I have a S1 Stagea RS4 auto with the under dash hand brake + release handle, I've just had the rear brake pads replaced and last night I noticed the (!) symbol flickering on & off whilst driving.

Is there a sensor for this light? Or do I just need to find the hand brake cable and apply some grease?

Any thoughts?

The switch should be on the rearward side of the foot brake you use for parking. Its a peg type that extends out ward to form the earth for the circuit when you depress this lever.

Having rear pads replaced wont help your park brake position as the park brake is the internal hub type (Pretty sure). If you have noticed an improvement in your park brake its possible there has been an adjustment made to your cable under the dash rather than at the rear wheels.

Could be the switch has been knocked loose?

Try releasing the park brake then get your toe under the pedal and pull it back a bit.....

I still have the same problem. At first I had to put my foot under the pedal to make it release, then it stuck altogether.

I fixed it by disconnecting it. Maybe one day I will try again and also make the ABS light go OFF.

Which cable seizes? Is it the one from the dash to the splitter, or one of the wheel cables?

Generally, the inner sheath rusts and damages the plastic coating on the cable, which makes it jam. No amount of lube down the sheath will free them up.

I know it's pretty obvious, but if you can work out which cable it is; there are companies that can manufacture factory style, plastic coated inner wire replacement cables.

I'm sure Nissan replacement cables will be fairly pricey.

The rusty cable may be the answer I am looking for. The 25G came from a salty road area in Japan. While repairing the smash damage we found several patches of quite serious rust and had it all cut out and repaired. Soon as it is driveable this week will put it on the hoist and check it out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...