Jump to content
SAU Community

N/a Skyline Question

Nibibo

By Nibibo,
in Engines & Forced Induction

 Share

Recommended Posts

mad082 Grand Master

mad082

Posted
Posted

So I've been told that Supra's drink petrol like its water.

Well I can give you the exact answer your looking for.

I get a good 425KM running on a full tank of Premium 98 before the empty light comes on. I believe it could do at least 450KM before I start running on fumes, but I tend not to risk it, although I do plan to run completely dry until my 34 becomes dehydrated to the point the engine shuts off just to see the MAXIMUM it can do on a full tank.

Gotta get myself a Jerry can first.

But to answer your question, 425KM on full tank of 98. Auto R34 25GT with RB25DE, no mods. Costs me about $140 a week though to run, since it's my daily and I drive it to city and back most days.

you should have roughly 10L of fuel left in the tank once the light comes on. in the case of my commodore though, i drove from gympie to noosa (just over 60kms) with the light on and then filled up to find i still had about 10L left in the tank. in the pulsar though, the light comes on fully with about 8L to go, but starts coming on then going off at about 11L to go.

back on topic though, if you want something RWD with better fuel economy than a skyline or supra, then get a silvia. the SR20 is a more fuel effecient motor.

Vera Community Regular

Vera

Posted
Posted

Don't know if your being sarcastic or not :unsure:

But if legit question, you don't have a fuel warning light on your cluster?

not being sarcastic, looking back now the post does sound very dumb.

I actually dont have one, looked real hard at the dash too. I managed to run my tank almost empty to see if anything lights up.

I've heard of other skylines being like this, but im not concerned with it so never bothered looking it up.

I was under the idea that the na models, being the cheaper ones, nissan might have skipped over that.

aussietroy Proficient

aussietroy

Posted
Posted

mines an auto n/a and i get around 400-450kms out of a tank of 95 mixed highway and town, good weeks i can push 500 before running on fumes, mostly highway .... but if you put your foot down it can easily only do 300-350 flogged around town ....

xntrq Veteran

xntrq

Posted
Posted

not being sarcastic, looking back now the post does sound very dumb.

I actually dont have one, looked real hard at the dash too. I managed to run my tank almost empty to see if anything lights up.

I've heard of other skylines being like this, but im not concerned with it so never bothered looking it up.

I was under the idea that the na models, being the cheaper ones, nissan might have skipped over that.

My 34 is NA. maybe a pre-R34 thing? or perhaps your LED blew out.

mad082 Grand Master

mad082

Posted
Posted

not being sarcastic, looking back now the post does sound very dumb.

I actually dont have one, looked real hard at the dash too. I managed to run my tank almost empty to see if anything lights up.

I've heard of other skylines being like this, but im not concerned with it so never bothered looking it up.

I was under the idea that the na models, being the cheaper ones, nissan might have skipped over that.

they certainly have one. all modern cars do. there would probably be some sort of regulation that requires it.

it may be that the bulb is blown or the sensor in the tank is faulty.

i'm trying to remember where it is in the r33. i have a feeling it may be in the same cirlce as the fuel gauge, rather than being a seperate light like the handbrake light, etc. but if someone has a cluster handy, they could just remove the bulbs at the back and shine a torch through and you would see what each bulb does when you look at it from the front

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • tidi0x
      Nismo GT Pro LSD configurations

      By tidi0x · Posted

      I have wasted too much time on this, more than I am willing to admit. I hope someone can set the record straight for me.  I want to replace my Nismo (non GT pro, non GT) standard 2 way in my R33 GTST with a 1.5 way... Ideally I want to get an ATS 1.5 way Carbon LSD, but I don't want to reuse my 29 spline 5x1 axle stubs, and new 30 spline 5x1's are impossible to get a hold of ($$$), and I don't want to drop the cash on going to 6x1 stubs and axles ATM. Which leads me to the Nismo GT Pro 38420-RSS15-B5 or RSS20, as they come with new axle stubs meant for the diff, and is "Convertible" from a 2 way or 1.5 way to "Other ways", but that is where I am stuck as the documentation is a bit all over the place.  To sum up what I have found I believe the all the Nismo GT Pro PN's are convertible from 2 way, 1.5 way, and 1 way; but Nismo sells 2 skus (2 & 1.5) so people do not have to disassemble to convert it.  I found this thread on 350z but it left the question unanswered. https://my350z.com/forum/engine-and-drivetrain/620032-nismo-gt-pro-lsd-1-5-vs-2-way-and-torque.html  Essentially the way I think it all works out is like follows...  2 way  1 way  and 1.5 way would be the center pinion shaft in the 1 way block, but with the with the center flipped 180*. So the ramped side of the pinion would face the 1 way gate and act like a ramp.    I can only get my hands on the 2 way in the states, and I am not trying to get stuffed on tariffs by ordering from Japan or anywhere else. I want to confirm that if I get the 2 way I can convert it to the 1.5.     
    • StevenJames32
      Single Turbo Conversion Lines.

      By StevenJames32 · Posted

      Hi everyone, I have purchased my first GTR and I want to do a single turbo conversion to it. I've been doing as much research as i can and there are a few things that I can find and need to know. I need to run a coolant feed, coolant return, oil feed and oil return for my turbo setup. Here's what I know so far: On the hot side of the rb26 there is coolant feed, oil feed and oil return. Coolant return will be going around the front of the engine to where the thermostat is located. I will need to block off the rear oil return port. I will be running a turbosmart boost solenoid so any of the factory boost stuff wont be needed. Now onto what I don't know: 1. What do I do with the coolant / vacuum hardlines that run around the back of the motor?. 2. What do I block off or loop or move or remove?. I will be running the OEM intake manifold. 3. Is there anything in particular I need to buy for the cold side of the rb26?. I already have the intercooler and pipes sorted. If you have any pictures or information it would be appreciated. Thanks....  
    • Murray_Calavera
      "Cheap" bolt on turbo on RB25DET NEO

      By Murray_Calavera · Posted

      The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • joshuaho96
      "Cheap" bolt on turbo on RB25DET NEO

      By joshuaho96 · Posted

      Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
    • GTSBoy
      "Cheap" bolt on turbo on RB25DET NEO

      By GTSBoy · Posted

      Intake manifold is not a part of the issue. The turbo bolts to the exhaust manifold. That is easy. But close your eyes and picture the physical situation. That is a T3 flange on the manifold and a T3 flange on the turbo. As long as any new turbo has a T3 flange on the exhaust housing, that exhaust housing will bolt to the exhaust manifold. This places the exhaust housing in the same place as the stock one. But now move your mental attention a little further forward. The location of the compressor housing is set by the length of the turbo's core. The stock turbo had a long core. Let's say that it is..... 100mm long. So that would place the compressor housing 100mm forward of the exhaust housing. But a highflow, might well have a centre core that is shorter. Let's say that it is only 70mm long. Now the compressor housing will be 30mm further back in the engine bay than the stock one. This DOES move the turbo's compressor outlet backwards. It also moves the compressor's inlet backwards. You will very likely have to do some work to both the inlet and outlet piping to make everything connect again. I am not say this to make it out to be a bigger deal than it is. I am just pointing out that "bolt on" is sometimes not quite bolt on. The highflow from GCG that Murray linked above (https://gcg.com.au/turbo-charger-upgrade-skyline-gtst-2iu-xtrgts-s1.html ) uses a core that is the same length as the stock core, and so does not require this extra work. It will look very much like the stock turbo. No-one uses GTR turbos of any flavour (stock, or aftermarket) in a single turbo application on RB20/25. It's not a thing. Yes, people have been putting on GT3076, GTX3076 (and bigger and smaller versions of those) and G30s (of various sizes) onto RB20/25 since forever. But these are not "bolt on". Everything except the 4 bolts to the exhaust manifold change with these. And genuine Garretts are expensive. Non-gen, like Pulsar, etc, are cheaper, variously as good or nearly as good. But still not bolt on. No-one in the right mind would pay for an HKS turbo. Not in this modern day and age. Well, yes, the GCG highflow. You could ask HG what he can do to make the compressor housing sit in the original location. There are surely others doing highflows around the world. And some of the eBay/Temu ones (as reported by Dose) work and don't die. Bit of a lottery though. I would send your turbo to GCG (here in Oz) to be highflowed if you want a trivial no-extra-work option. But seriously, the work required to change inlet and outlet piping is not that hard. That's a boost control problem, not a turbo problem.
×
×
  • Create New...